DATASHEET KEY FEATURES ® MPC7455 PowerPC processor The MVME5500 is the latest I/O to the outstanding processor at 1 GHz ţ agship of the Motorola VME performance, the MVME5500 product line, enabling higher provides dual 64-bit, 33/66 MHz 256KB of on-chip L2 cache and levels of performance in a single PCI buses. Each PCI bus has 2MB of L3 cache VMEbus slot. The MVME5500 a PMC site supporting cards AltiVec coprocessor for utilizes the MPC7455 processor running at 33 or 66 MHz. The high-performance computational running at 1 GHz, which is ideal Universe II VME interface applications for data intensive applications. and PMCspan connector are isolated from the PMC sites on 512MB of on-board 133 MHz The MVME5500 provides more a dedicated 33 MHz PCI bus SDRAM ECC memory and than just better processor segment so that both PMC 512MB additional memory via performance; it also provides sites are capable of 66 MHz a memory mezzanine card for a balanced performance from operation. The MVME5500 total of 1GB of memory the processor, memory, dual also offers a Gigabit Ethernet independent local buses and Two banks of soldered ţ ash interface, a 10/100BaseTX I/O subsystems. The powerful memory (32MB and 8MB) Ethernet interface and two Marvell system controller, serial ports. All of this adds up Dual independent 64-bit PCI with support for a 133 MHz to a set of well-balanced, buses and PMC sites with a bus host bus and a 133 MHz high-performance subsystems speed of up to 66 MHz SDRAM memory bus, is well for unparalleled performance. matched to the high speed Gigabit Ethernet interface plus processor. To match the system an additional 10/100BaseTX Ethernet interface 64-bit PCI expansion mezzanine connector allowing up to four more PMCs I/O compatibility with MVME51xx family Single VME slot even when fully conŢ gured with two PMC modules or one PMC module and an add-on memory mezzanine Support for processor PMCs (PrPMCs) The MVME5500 series is designed to meet the needs of OEMs including those in defense and aerospace, industrial automation and medical imaging market segments. Customers looking for a technology refresh for their application while maintaining backward compatibility with their existing VMEbus infrastructure can upgrade to the MVME5500 series and take advantage of the enhanced performance features. MVME5500 Series VME Single-Board Computer SDRRAM L3 Cache COM1 COM2 Mezzanine 2MB FP I/O Planar 512MB Battery Flash 32MB SDRRAM NVRAM EIA232 EIA232 (soldered) MPC7455 133 MHz RTC 8MB 1 GHz 512 MB (soldered) UART UART PCI Bridge & A32/D64-bit, 133 MHz Memory Controller 66 MHz PCI Local Bus Discovery – A32/D64-bit Gigabit PCI 66 MHz PCI Local Bus Bridge Ethernet – A32/D64-bit Controller 33 MHz PCI Local Bus – A32/D64-bit Ethernet PMC IPMC 10/100BaseTX Port 1 Slot 2 Slot 1 PHY PMCspan 10/100/1000 Connector BaseTX Universe II FP I/O PMC PMC FP I/O FP I/O Port 2 10/100BaseTX P2 P1 FP I/O BACKWARD COMPATIBILITY The MVME5500 continues the direction that Motorola started with the MVME5100 series of providing a migration path from Motorola’s embedded controllers and single-board computers (SBCs) to a single platform. This migration path enables OEMs to support varying I/O requirements with the same base platform, simplifying part number maintenance, technical expertise requirements and sparing. The MVME5500 series offers customers a migration path from the MVME2300, MVME2400, MVME2600, MVME2700 and MVME5100 boards to allow them to take advantage of features such as the MPC7455 processor, Gigabit Ethernet and dual independent 33/66 MHz PMC sites. IPMC MODULES The IPMC761 and IPMC712 are optional add-on PMC modules that provide backward compatibility with previous generation Motorola products (such as MVME2600, MVME2700 and MVME5100 in IPMC mode) using the MVME761 or MVME712M transition module. IPMC modules provide rear I/O support for the following: One single-ended Ultra Wide SCSI port One parallel port Four serial ports (two or three async and one or two sync/async, depending on module) With an IPMC installed, one PMC slot is still available, providing support for OEM product customization. P2 I/O MODES The MVME5500 series supports two, jumper-confi gurable P2 I/O modes: PMC mode and IPMC mode. PMC mode is backward compatible with the MVME2300/MVME2400 and MVME5100 in PMC mode. In PMC mode, 64 pins from PMC slot 1 and 46 pins from PMC slot 2 are available on P2 for PMC rear I/O. In IPMC mode, the MVME5500 series supports legacy MVME761 or MVME712M I/O modules (with limited PMC I/O) when an IPMC761 or IPMC712 PMC card is populated in PMC slot 1. In this confi guration, PMC slot 2 contains some signals that are reserved for extended SCSI. TRANSITION MODULES The MVME761 transition module provides industry-standard connector access to the IEEE 1284 parallel port, a 10BaseT or 100BaseT port via an RJ-45 connector, two DB-9 connectors providing access to the asynchronous serial ports confi gured as EIA-574 DTE and two HD-26 connectors providing access to the sync/async serial ports. These serial ports, labeled as Serial 3 and Serial 4 on the faceplate of the MVME761, are individually user-confi gurable as EIA-232, EIA-530, V.35, or X.21 DCE or DTE via the installation of Motorola Serial Interface Modules (SIMs). A P2 adapter board provides interface signals to the MVME761 transition module. Two separate P2 adapter boards are available: one for 3-row backplanes and one for 5-row backplanes. The 3-row P2 adapter board provides connection for 8-bit SCSI. A 5-row P2 adapter board supports 16-bit SCSI and PMC I/O. 2 MVME5500 The MVME712M transition module provides industry-standard connector access to the Centronics parallel port, a narrow SCSI port, and four DB-25 connectors providing access to the asynchronous/synchronous serial ports jumper confi gurable as EIA-232 DCE or DTE. A P2 adapter board provides interface signals to the MVME712M transition module. The 3-row P2 adapter board also provides connection for 8-bit SCSI. To gain access to the additional user- defi nable I/O pins provided via the 5-row VME64 extension connector, a special P2 adapter board is available. This adapter panel replaces the traditional 3-row P2 adapter board and extends its capability by providing access to the PMC I/O pins. SOFTWARE SUPPORT FIRMWARE MONITOR Firmware must fulfi ll the traditional functions of power-on self-test (POST), initialization, low-level setup and debug, and operating system booting. Motorola’s innovative fi rmware (known as MOTLoad) that is resident on the MVME5500 exceeds these requirements with expanded features such as interrupt driven I/O, more comprehensive power-up tests and extensive diagnostics with new scripting capability. And of course, MOTLoad provides a debugger interface similar to the time proven “bug” interface on previous VMEbus boards from Motorola. OPERATING SYSTEMS AND KERNELS WindRiver Systems VxWorks, TimeSys Linux, Green Hills Software INTEGRITY and LynuxWorks LynxOS are available for the MVME5500. LIBRARIES VSI/Pro VSIPL libraries from MPI Software Technology are available on the MVME5500. BETA 4.0 NDDS from Real Time Innovations (RTI) running over GbE and Native VME are available on the MVME5500 through RTI. SPECIFICATIONS PROCESSOR NVRAM Microprocessor: MPC7455 Capacity: 32KB (4KB available for users) Clock Frequency: 1 GHz Cell Storage Life: 50 years at 55° C On-chip L1 Cache (I/D): 32KB/32KB Cell Capacity Life: 5 years at 100% duty cycle, 25° C On-chip L2 Cache (I/D): 256KB Removable Battery: Yes L3 Cache: 2MB COUNTERS/TIMERS SYSTEM CONTROLLER TOD Clock Device: M48T37V Marvell GT-64260B Real-Time Timers/Counters: Eight, 32-bit programmable Watchdog Timer: Time-out generates reset MAIN MEMORY VMEBUS INTERFACE: ANSI/VITA 1-1994 Type: PC133 ECC SDRAM VME64 (IEEE STD 1014) Speed: 133 MHz Controller: Tundra Universe II Confi gurations: 512MB in two banks DTB Master: A16-A32; D08-D64, SCT, BLT Capacity: 512MB on-board, expandable to 1GB with add-on memory mezzanine card. DTB Slave: A24-A32; D08-D64, BLT, UAT Note: If a PMC module is plugged into PMC slot 1, the Arbiter: RR/PRI memory mezzanine card cannot be used because the Interrupt Handler/Generator: IRQ 1-7/Any one of PMC module covers the memory mezzanine connector. seven IRQs System Controller: Yes, jumperable or auto detect FLASH MEMORY Location Monitor: Two, LMA32 Type: EEPROM, on-board programmable Capacity: 40MB total in two banks of 32MB and 8MB, both soldered Write Protection: 32MB of surface-mount fl ash is write protectable via jumper MVME5500 3 ETHERNET INTERFACES PCI EXPANSION CONNECTOR Port 1 Address/Data: A32/D32/D64 ® Controller: Intel 82544EI Gigabit Ethernet controller PCI Bus Clock: 33 MHz Interface Speed: 10/100/1000Mbps Signaling: 5V Connector: Routed to front panel RJ-45 Power: +3.3V, +5V, ±12V Connector: 114-pin connector located on MVME5500 planar, same location as on MVME5100 planar Port 2 Controller: Controller integrated into GT-64260B system controller POWER REQUIREMENTS Interface Speed: 10/100Mbps +5V ± 5% Connector: Routed to front panel RJ-45 or optionally MVME5500-0163: 6.7 A typ., 8.0 A max. routed to P2, RJ-45 on MVME761 MVME5500-0163 with memory mezzanine: 7.5 A typ., 9.0 A max. ASYNCHRONOUS SERIAL PORTS MVME5500-0163 with IPMC712/761: 7.6 A typ., 9.2 A max. Controller: Two TL16C550C UARTs Note: In a 3-row chassis, PMC current should be limited Number of Ports: Two, 16550 compatible to 19.8 watts (total of both PMC slots). In a 5-row chassis, Async Baud Rate, bps max.: 38.4K EIA-232, 115Kbps raw PMC current should be limited to 46.2 watts (total of both Connector: Routed to front panel RJ-45; one on planar PMC slots). for development use BOARD SIZE DUAL IEEE P1386.1 PCI MEZZANINE CARD Height: 233.4 mm (9.2 in.) SLOTS Depth: 160.0 mm (6.3 in.) Address/Data: A32/D32/D64, PMC PN1, PN2, PN3, PN4 Front Panel Height: 261.8 mm (10.3 in.) connectors Width: 19.8 mm (0.8 in.) PCI Bus Clock: 33/66 MHz Max. Component Height: 14.8 mm (0.58 in.) Signaling: 3.3V or 5V, confi gurable with keying pin Power: +3.3V, +5V, ±12V Module Types: Two single-wide or one double-wide, front panel or P2 I/O, PMC and PrPMC support Note: If a PMC module is plugged in PMC slot 1, the memory mezzanine card cannot be used because the PMC module covers the memory mezzanine connector. IPMC MODULES PMC INTERFACE SYNCHRONOUS SERIAL PORTS Address/Data: A32/D32/D64, PMC PN1, PN2, PN3, PN4 Controller: 85230/8536 connectors Number of Ports: Two (IPMC761); one (IPMC712) PCI Bus Clock: 33 MHz Confi guration: IPMC761: TTL to P2 (both ports), SIM Signaling: 5V confi gurable on MVME761; IPMC712: EIA-232 to P2 Module Type: Basic single-wide; P2 I/O Baud Rate, bps max.: 2.5M sync, 38.4K async Oscillator Clock Rate (PCLK): 10 MHz/5 MHz SCSI BUS Controller: Symbios 53C895A ASYNCHRONOUS SERIAL PORTS PCI Local Bus DMA: Yes, with PCI local bus burst Controller: 16C550 UART; 85230/8536 Asynchronous (8-bit mode): 5.0MB/s Number of Ports: Two (IPMC761); three (IPMC712) Ultra SCSI: 20.0MB/s (8-bit mode), 40.0MB/s (16-bit mode) Confi guration: EIA-574 DTE (IPMC761); EIA-232 (IPMC712) Note: 16-bit SCSI operation precludes the use of some PMC slot 2 signals. Async Baud Rate, bps max.: 38.4K EIA-232, 115Kbps raw 4 MVME5500 PARALLEL PORT POWER REQUIREMENTS Controller: PC97307 (Additional power load placed on MVME5500 with IPMC installed) Confi guration: 8-bit bi-directional, full IEEE 1284 support; Centronics compatible (minus EPP and ECP on IPMC761 IPMC712 MVME712M) +5V: 0.5 A max. 0.5 A max. Modes: Master only +3.3V: 0.75 A max. 0.75 A max. TRANSITION MODULES I/O CONNECTORS MVME761 MVME712M Asynchronous Serial Ports: Two, DB-9 labeled as COM1 Three, DB-25 labeled Serial 1, and COM2 Serial 2 and Serial 3 Synchronous Serial Ports: Two, HD-26 labeled as Serial 3 One, DB-25 labeled as Serial 4 and Serial 4 (user-confi gurable via installation of SIMs); two 60-pin connectors on MVME761 planar for installation of two SIMs Parallel Port: HD-36, Centronics compatible D-36, Centronics compatible Ethernet: 10BaseT or 100BaseT, RJ-45 Not available SCSI: 8- or 16-bit, 50- or 68-pin 8-bit, standard SCSI D-50 connector via P2 adapter BOARD SIZE Height: 233.4 mm (9.2 in.) Depth: 80.0 mm (3.1 in.) Front Panel Height: 261.8 mm (10.3 in.) Front Panel Width – MVME761: 19.8 mm (0.8 in.) Front Panel Width – MVME712M: 39.6 mm (1.6 in.) ALL MODULES ENVIRONMENTAL ELECTROMAGNETIC COMPATIBILITY (EMC) Operating Non-operating Intended for use in systems meeting the following regulations: Temperature: 0° C to +55° C –40° C to +85° C (inlet air temp. U.S.: FCC Part 15, Subpart B, Class A (non-residential) w/forced air cooling*) Canada: ICES-003, Class A (non-residential) *Note: Reference cooling requirements section of the user’s manual. Humidity (NC): 5% to 90% 5% to 90% Motorola board products are tested in a representative Vibration: 1 G sinusoidal, system to the following standards, results pending for 5–100 Hz confi gurations with IPMC712: CE Mark per European 2 axes horizontal EMC Directive 89/336/EEC with Amendments; Emissions: and vertical EN55022 Class A; Immunity: EN55024 (NEBS1) DEMONSTRATED MTBF SAFETY Predicted MTBF 207,058 hours, calculated using Bellcore All printed wiring boards (PWBs) are manufactured Standard: Issue 6, Method 1, Case 3 with a fl ammability rating of 94V-0 by UL recognized manufacturers. MVME5500 5 ORDERING INFORMATION Part Number Description MVME55006E-0161 1 GHz MPC7455 PowerPC processor, 512MB SDRAM, Scanbe handles 6E MVME55006E-0163 1 GHz MPC7455 PowerPC processor, 512MB SDRAM, IEEE handles 6E Memory RAM5500-007 512MB memory mezzanine expansion card Related Products IPMC7125E-001 Multifunction rear I/O PMC module; 8-bit SCSI, Ultra Wide SCSI, one parallel port, three async and one sync/async serial ports 5E MVME712M5E Transition module with one DB-25 sync/async serial port, three DB-25 async serial port, one AUI connector, one D-36 parallel port, and one 50-pin 8-bit SCSI; includes 3-row DIN P2 adapter board and cable 5E MVME7615E-001 Multifunction rear I/O PMC module; 8-bit SCSI, one parallel port, two async and two sync/async serial ports. Transition module with two DB-9 async serial port connectors, two HD-26 sync/async serial port connectors, one HD-36 parallel port connector, one RJ-45 10/100 Ethernet connector; includes 3-row DIN P2 adapter board and cable (for 8-bit SCSI) 5E MVME7615E-011 Transition module with two DB-9 async serial port connectors, two HD-26 sync/ async serial port connectors, one HD-36 parallel port connector, one RJ-45 10/100 Ethernet connector; includes 5-row DIN P2 adapter board and cable (for 16-bit SCSI); requires backplane with 5-row DIN connectors 5E PMCSPAN15E-002 Primary PMCSPAN-002 with original VME Scanbe ejector handles 5E PMCSPAN15E-010 Secondary PMCSPAN-010 with original VME Scanbe ejector handles 5E Documentation V5500A/IH MVME5500 Single-Board Computer Installation and Use V5500A/PG MVME5500 Single-Board Computer Programmer’s Reference Guide VME761A/IH MVME761 Transition Module Installation and Use VME712MA/IH MVME712M Transition Module Installation and Use MOTLODA/UM MOTLoad Firmware Package User’s Manual VIPMCA/IH IPMC712/761 I/O Module Installation and Use PMCSPANA/IH PMCspan PMC Adapter Carrier Board Installation and Use Documentation is available for online viewing and ordering at www.motorola.com/computer/literature SOLUTION SERVICES Motorola provides a portfolio of solution services optimized to meet your needs throughout the product lifecycle. Design services help speed time-to-market. Deployment services include global 24x7 technical support. Renewal services enable product longevity and technology refresh. And solution extras include enhanced warranty and repairs. Sales OfŢ ces Tempe, AZ U.S.A. 1 800 759 1107 or +1 602 438 5720 Tel Aviv, Israel +972 3 568 4385 Paris, France +33 1 69 35 25 88 Shanghai, China +86 215292 5693 Munich, Germany +49 89 608 14-0 Tokyo, Japan +81 3 5424 3101 Loughborough, UK +44 1509 634300 Hong Kong, China +852 2966 3209 This document identiŢ es products, their speciŢ cations, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present or future availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Motorola may sell products. A prospective buyer should exercise its own independent judgment to conŢ rm the suitability of the products for particular applications. Motorola reserves the right to make changes, without notice, to any products or information herein which will, in its sole discretion, improve reliability, function, or design. Motorola does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes Motorola’s licensee, licensee’s transferees, and licensee’s customers and users. Availability of some of the products and services described herein may be restricted in some locations. www.motorola.com/computing MOTOROLA and the Stylized M Logo are registered in the U.S. Patent and Trademark OfŢ ce. PowerPC is a trademark of IBM Corp. and used under license. Intel is a registered trademark of Intel Corporation or its subsidiaries in the U.S. and other countries. All other product or service names are the property of their respective owners. © Motorola, Inc. 2006 MVME5500-D8 02/06