CPX8221 TM High Availability CompactPCI System ® � 21-slot CompactPCI passive backplane with dual domains • Domain A with six I/O slots • Domain B with 11 I/O slots ® � PowerPC 750 controller CPU option � Hot-swappable CPU and I/O boards � Up to three 350W hot-swappable, N+1 redundant power supplies � Wide ranging AC and DC input versions � Three hot-swappable, N+1 redundant fans with filter options � Front-access service and installation of CompactPCI boards, fans and power supplies � Rear connection of CPU I/O allows card removal without disconnecting field wiring � Detection and remote reporting of power, temperature and fan fail conditions � NEBS compliant alarm status display panel ® � Support for Linux and other popular operating systems Ideal solution for telecom infrastructure applications The CPX8221 system provides an ideal solution for telecom infrastructure applications that requires a high concentration of network blades in a 19-inch rack. Based on CompactPCI technology, CPX8221 systems have built-in redundancy for active system components—including system-slot CPU boards—enabling active modules to be exchanged for repair or upgrade while the system continues to operate. Designed as a carrier-grade platform for operation in NEBS and ETSI environments, the CPX8221 is particularly well suited for switching applications and deployment within unattended sites. Standards Compliance ETSI Standards Compliance The CPX8221 family of systems is intended to meet the requirements of the European Telecom Standard (ETSI) NEBS including: The CPX8221 family of systems is intended to meet the • Equipment Engineering (EE): Environmental conditions requirements of the Bellcore standards, Network Equipment and environmental tests for telecommunications equip- Building System (NEBS) Requirements: Physical Protection, ment, ETS 300 019-1-3 GR-63-CORE and Electromagnetic Compatibility and Electri- • Storage: ETS 300 019-1-1, for Class 1.2 equipment cal Safety-Generic Criteria for Network Telecommunication • Transportation: ETS 300 019-1-2, for Class 2.3 equip- Equipment, GR-1089-CORE. The product is currently being ment tested to the requirements for NEBS Level 3 criteria. Criteria ETSI Criteria NEBS Specification Reference Specification Reference Temperature Storage: –25° C to 55° C IEC 60068-2-1 Trans.: –40° C to 70° C IEC 60068-2-2 Temperature Normal: 5° C to 40° C GR-63-CORE, R4-7 Operating: –5° C to 45° C IEC 60068-2-14 Short-term: –5° C to 55° C Relative Storage: 10% to 100% RH (non-con- IEC 60068-2-56 Relative Normal: 5% to 85% RH GR-63-CORE, R4-7 Humidity Humidity densing and condensing) IEC 60068-2-30 Short-term: 5% to 90% RH Trans.: 95% @ –40° C to 45° C Office Vibration 0.1 G @ 5–100 Hz with 0.1 GR-63-CORE, R4-56 Operating: 5% to 95% RH (non-con- octave/min GR-63-CORE, R4-57 densing and condensing) 1.5 G @ 100–500 Hz with 0.25 Vibration Storage: 1.5 mm @ 2–9 Hz, 0.5 G @ 9– IEC 60068-2-6 octave/min 200 Hz IEC 60068-2-36 Transportation 5–50 Hz @ 0.1 octave/min GR-63-CORE, R4-58 Trans. sinusoidal: 3.5 mm @ 2–9 Hz, Vibration 50–500 Hz @ 0.25 octave/min 1 G @ 9–200 Hz, 1.5 Gs @ 200–500 Hz 2 3 Earthquake Zone 4 GR-63-CORE R4-44 to Trans. random: 1 m /s @ 10–200 Hz, 2 3 O-55 0.3 m /s @ 200–2000 Hz. Operating: 1.5 mm @ 2–9 Hz, 0.5 G @ Drop Packaged: 300 mm drop height GR-63-CORE, R4-41 9–200 Hz Unpackaged: 50 mm drop GR-63-CORE, R4-43 height Shock Storage, Type I: 4 Gs @ 22 ms IEC 60068-2-27 Trans., Type I: 30 Gs @ 11 ms IEC 60068-2-29 Altitude –60 to 1800 m ASL without GR-63-CORE, R4-8 Operating: 4 Gs @ 22 ms temp. derating GR-63-CORE, R4-9 1800 to 4000 m ASL with temp. GR-63-CORE, O4-9 Earthquake 5 G, 0.3 to 35 Hz IEC 60068-2-57 derating Drop Trans.: 0.4 m free fall IEC 60068-2-32 Acoustic Noise 60 dBA @ 600 mm GR-63-CORE, O4-62 Load Storage: 5 kPa N/A Heat Dissipation Documentation GR-63-CORE, R4-11 Trans.: 10 kPa 2 300/w/m /m max per shelf GR-63-CORE, R4-12 Altitude –471 to 3708 m ASL N/A 38° C max. aisle-facing surface GR-63-CORE, O4-13 Water Trans.: 6 mm/min IEC 60068-2-18 temp. @ 26° C ambient Acoustic Noise 7.2 bels @ 1 m ETS 300 753 Fire Resistance All material UL94V-1 or better. GR-63-CORE, R4-14 to and Materials ISO 7779 See GR-63-CORE, Section 4.2 O4-40 Fire Resistance All material UL 94V-1 or better UL1950 Illumination See GR-63-CORE, Section 4.7 GR-63-CORE, R4-63 to and Materials UL94 O4-69 BS2782 Part 1 3 Airborne Sulfate: 30 μg/m GR-63: R4-59, O4-60 (ISO 181) 3 Contaminant Nitrite: 12 μg/m 3 3 Airborne S0 : 0.3/1.0 mg/m N/A Volatile organics: 12 μg/m 2 3 Contaminant H S: 0.1/0.5 mg/m Sulfur Dioxide: 12 ppb 2 Salt mist: sea and road salt Hydrogen Sulfide: 40 ppb 3 CL : 0.1/0.3 mg/m Ammonia: 50 ppb 2 3 HCl: 0.1/0.5 mg/m NO: 50 ppb 3 NO : 0.5/1.0 mg/m NO : 250 ppb x 2 3 NH : 1.0/3.0 mg/m HNO : 50 ppb 3 3 3 HF: 0.01/0.03 mg/m Ozone: 250 ppb 3 O : 0.05/0.1 mg/m HCL + Cl : 6 ppb 3 2 2 Dust sedimentation: 0.4 mg/m h 3 Dust suspension: 5 mg/m Specifications Power Supplies and Fan Modules Power Supplies and Fan Modules Specifications Chassis The CPX8221 uses up to three 350-watt hot-swappable power sup- plies in an N+1 redundant configuration. Each supply is load sharing Size: 21.00" [533 mm] high (12U), 18.90" [480 and diode protected. An industry-standard, open-frame supply is mm] wide including mounting flanges, enclosed in a sled assembly that supports the power supply, fan 17.13" [435 mm] deep from mounting assembly, blind mate connectors, power supply/fan control board flanges and interconnect wiring harness. Either AC or DC versions are avail- Weight: Approx. 30 lbs. [13.6 kg] unloaded able. Fan-only sled assemblies are available and are required for Approx. 70 lbs. [31.85 kg] fully loaded unfilled power supply bays to ensure managed cooling of the system. Mounting: Per EIA Standard RS-310-C in 19" rack or Cooling Features 23" rack with mounting brackets • Three hot-swappable, N+1 modules in system Slots: 21 hot-swap-capable 4HP CompactPCI • DC tube axial fan slots including two CPU slots, two HSC • Cooling sensor detects airflow and temperature changes bridge slots and seventeen I/O slots. • Air filter option Power Supplies/Fans: Three bays, front-accessible • Software monitoring and speed control Airflow: Front inlet, rear exhaust • LED status indicators ESD Grounding: Two ESD ground points, one front and one Electrical Specifications rear Power Factor: 0.98 min. at full load, nominal line (AC Earth Ground: Two points at rear per NEBS requirements only) Metal: Aluminum alloy, 5052-H32 Inrush Current: 40 A peak @ 115 VAC for one line cycle Metal Plating: 40 A peak @ –36 VDC within 4 ms Chemical film per MIL-C-5541, Class 3, clear Efficiency: > 65% @ full load, nominal line Slot, LED, and Switch Black silk screen on white removable over- Output Power: 350 watts in this application Marking: lays Hold-Over Storage: 20 ms at full load @ 90 VAC PowerPC High-Availability CPU Card Transient Response: All outputs return to 1% within 2 ms of a Processor: 366 MHz PowerPC 750 25% load change Memory: Dynamic Load: Up to 256MB DRAM, 1MB L2 cache, The supply operates properly when sub- ™ CompactFlash IDE flash drive option jected to a 10% load delta with a 50% duty cycle, from 0 to 2 MHz I/O: EIDE, 10/100 Ethernet, USB, serial (sync/ Over Voltage Protection: async), parallel +5V output < 6.4 VDC +3.3V output < 4.2 VDC I/O Access: Front Short Circuit Protection: Short between outputs causes latch off PMC Site: Yes Module DC Output Hot Swap Controller (HSC) Bridge Card (Total combined output loading not to exceed 350 watts) Form Factor: 80 mm rear transition Voltage Regulation Min. Max. Peak Ripple Control: CompactPCI bus and slot control per Load Load Load 5 P/P CompactPCI Hot Swap Specification Sec. Max Alarm Status Yes Registers: +5.06V ± 3% 0.5 A 40.0 A — 50 mV Hot-Swappable: Yes +3.36V ± 3% 0.5 A 40.0 A — 34 mV +12.1V ± 5% 0.3 A 8.0 A 10.0 A 120 mV Backplane –12.1V Domains: ± 5% 0.3 A 4.0 A — 120 mV Two; one 8-slot, one 13-slot, 64-bit CompactPCI Power Distribution Module Slots: One CPU slot, one HSC bridge slot, and Power Distribution Module six I/O slots in domain A; PCI Domain B has access to 11 I/O slots AC Input Version DC Power Distribution: Yes • 90–132 VAC or 190–260 VAC input, auto selecting, Alarm Signal Routing: Yes 47–63 Hz Hot-Swappable Alarm Board • Double-pole rocker on/off switch and IEC AC input receptacle CompactPCI Slot LEDs: • 12 A maximum input current at 115 VAC Two for each slot; In Service and Out of Service • 6 A maximum input current at 230 VAC Telecom Status LEDs: Minor, major and critical DC Input Version Output: RJ-45 connector with dry relay contacts • –36 VDC to –72 VDC input • Double-pole circuit breaker with on/off switch and reset • Dual (redundant) input terminal blocks, diode protected • 30 A maximum input current at –48 VDC Reliability and Serviceability Software Support Reliability and Serviceability Software Support The redundant configuration characteristics of the CPX8221 provide Motorola Computer Group partners with selected software providers detection, isolation, notification and hot swap replacement of a failed to ensure a wide range of application availability within the frame- field replaceable unit (FRU). This method prevents degradation of work of the CPX8221 high availability environment. Additional infor- performance or loss of service during a single fault condition. mation can be obtained by contacting the partners listed below. Field Replaceable Units (FRUs) Operating Systems ® Field Replaceable Units Hot Swap Redundant MTTR* • LynxOS from LynuxWorks, www.lynx.com ® •VxWorks from Wind River Systems, www.wrs.com CompactPCI boards X X 5 min. • Linux (contact Motorola Computer Group) HSC/bridge board X X 5 min. PowerPC Firmware Power supply/fan modules X X 5 min. On-board PowerPC firmware expands features like power-up tests Power distribution module 5 min. with extensive diagnostics, and provides an evaluation and debug Alarm board X 5 min. tool for simple or high-level development support. It also supports booting of operating systems and/or real-time kernels. *Mean time to replace Ordering Information System MTBF CPX8221FSK01: Ordering Information 107,161 Note: System MTBF is demonstrated at accelerated life testing. Starter Kits Regulatory Compliance Starter kits provide a complete hardware platform designed to reduce Safety: CSA NRTL/C, VDE EN60950, CE Mark per European development time. In addition, operating systems and development Low Voltage Directive 72/23/EEC software is available from the Motorola Computer Group and selected partners. See the Software Support section. Also included is EMC: U.S.: FCC Part 15, Subpart B, Class A CPU-based debugger and diagnostics which provide self-testing and Canada: ICES-003, Class A system-level diagnosis including loop-back, register tests and mem- Europe: CE Mark per European EMC Directive 89/336/ ory address/data tests. EEC with Amendments; Emissions: EN55022 Class A; Starter Kit Part Description Immunity: EN50082-1 and EN55024 Number OEM Customization Services CPX8221FSK01 PowerPC Starter Kit - Pre-configured platform Motorola Computer Group provides a wide range of customization that contains: options, including: • 21-slot CompactPCI chassis with front I/O • Labeling, marking and paint options only • Electrical and/or mechanical modifications • Dual 366 MHz CPX750HA CPUs with 128MB • Hardware integration DRAM • Software integration • Dual hot swap controller bridges • Third-party device integration • Alarm panel • Single-point service and FRU point of contact • Three AC power supplies Contact your Motorola Computer Group Sales representative for CPX8221FSK02 PowerPC Starter Kit - Pre-configured platform additional information. that contains: • 21-slot CompactPCI chassis with front I/O • Dual 366 MHz CPX750HA CPUs with 256MB DRAM • Dual hot swap controller bridges • Alarm panel • Three AC power supplies www.motorola.com/computer 1-800-759-1107 Motorola Computer Group Worldwide Headquarters: 2900 S. Diablo Way, Tempe, AZ 85282 Sales Offices: United Kingdom: +44 (0) 1256 790555 • Asia Pacific and Japan: 852-2966-3209 • France: +33 (0) 1 64 86 64 00 • Germany: +49 (0) 611-3611 604 • East Mediterranean: 972-3-568-4388 • Canada & Central Pan America: 888-366-3624 • Eastern Pan America: 508-357-8260 • Western Pan America: 408-991-8634 Motorola and the stylized M logo are registered trademarks and the Intelligence Everywhere logo, Digital DNA and the Digital DNA logo are trademarks of Motorola, Inc. PowerPC is a registered trademark of International Business Machines Corporation and is used by Motorola, Inc. under license from International Business Machines Corporation. PhoenixBIOS is a common law trademark of Phoenix Technologies Ltd. CompactFlash is a trademark of SanDisk Corporation. CompactPCI is a registered trademark of PCI Industrial Computer Manufacturers Group. Linux is a registered trademark of Linus Torvalds. LynxOS is a registered trademark of LynuxWorks, Inc. VxWorks is a registered trademark of Wind River Systems, Inc. All other product or service names are the property of their respective owners. This datasheet identifies products, their specifications, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present or future availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Motorola may sell products. A prospective buyer should exercise its own independent judgement to confirm the suitability of the products for particular applications. Motorola reserves the right to make changes, without notice, to any products or information herein which will, in its sole discretion, improve reliability, function, or design. Motorola does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes Motorola’s licensee, licensee’s transferees, and licensee’s customers and users. Availability of some of the products and services described herein may be restricted in some locations. ® Reg. U.S. Pat. & Tm. Off. Copyright 2000, 2001 Motorola, Inc. C8221-D2 5/01