Datasheet CPV5300 CompactPCI Host Slot Processor High performance single-board computer providing I/O access from either front or rear ® Motorola’s CPV5300 is a high performance CompactPCI single-board ® computer powered by either a Pentium II or Pentium III processor mobile module. Highly integrated, it provides standard PC I/O plus USB, PCI EIDE, Ultra SCSI, AGP graphics and dual Fast Ethernet controllers with optional on-board ultra-thin floppy and 2.5" EIDE drives. Clever design allows I/O access from either the front or rear. And, all this occupies just two CompactPCI slots. The CPV5300 is designed to meet the needs of embedded application developers addressing high bandwidth industrial control and telephony applications. Typical applications include broadband data or intelligent network switching; CTI server; industrial control and automation; military and aerospace; and medical, scientific, or imaging products. ® � Intel processor mobile module including: ® –Pentium II or Pentium III processor –82440BX chipset –66/100 MHz system bus frequency � Up to 512MB system memory Ethernet Ethernet SCSI Video Kbd/Mouse LPT1 COM2 COM1 � Accelerated 2D graphics with 4MB video Dual Dual DIN RJ-45 RJ-45 Mini Dsub Dsub Dsub Dsub Dsub USB USB memory � Dual 10BaseT/100BaseTX Fast Ethernet LM78 System Monitor � Ultra SCSI On-Board IDE Hard Drive or Flash � Two Universal Serial Bus (USB) channels On-Board Floppy � Two asynchronous serial ports � One bi-directional parallel port 2D South Ethernet Ethernet Ultra Ultra AGP Bridge 10/100 10/100 SCSI I/O � PS/2 keyboard/mouse interface, real-time Video (PIIX4) clock, and watchdog timer Pentium II or III Bridge � PCI Enhanced IDE controller with support Mobile Module DRAM 440BX 512MB for up to four devices (CompactFlash CompactPCI 2 DIMM Bus and/or 2.5" EIDE hard drive) J1 J2 J4 J5 � On-board BIOS stored in 512KB Flash ROM � Optional ultra-thin 3.5" floppy drive � Supported by industry-standard operating ® systems such as Windows NT and ® VxWorks , with others to come IDE Ethernet Ethernet Video SCSI Floppy EIDE EIDE USBx2 Kbd/Mouse LPT1 COM2 COM1 CPV5300 Details CPV5300 DETAILS Intel Pentium II or Pentium III Processor Mobile Hot Swap Compatible Module The CPV5300 will allow other non-system slot For high-end embedded applications, the boards to be removed or added while the CPV5300 fully supports the Pentium II or chassis is powered up. Individual clocks for Pentium III processor mobile module. The each slot and access to the backplane processor is combined with the Intel 440BX ENUM# signal are in compliance with the PCI chipset resulting in exceptional PICMG 2.1 Hot Swap Specification. While hot processing capability. The mobile module swap of non-system slot boards is supported, contains 32KB of internal Level 1 cache the CPV5300 itself can not be inserted or memory as well as 256KB of Level 2 cache removed in a powered system. delivering rapid data access to complex On-Board Peripherals applications. Dynamic execution and dual The CPV5300 has an extensive array of independent buses are additional on-board I/O that is available from both the performance advantages. For continual front panel of the CPV5300 and/or the rear mobile module processor speed enhancement panel via the CPV5300CTM80 transition options, consult your Motorola sales board. Two serial, one parallel, two USB, PS/2 representative. mouse and keyboard, one IDE channel Memory (secondary), speaker, reset and floppy are The CPV5300 provides two 168-pin DIMM routed via CompactPCI connector J5; and one sites for on-board memory expansion. IDE channel (primary), SMBus (alarm), Ultra Organized as two separate memory banks, up SCSI, video and dual Ethernet are routed to 512MB of synchronous DRAM is through the backplane via CompactPCI supported. Memory size is detected by the connector J4. (CompactPCI connector J3 is system BIOS. not used.) 2D Accelerated Graphics CompactPCI Bus ™ A CHIPS 69030 HiQVideo accelerator with Designed to the CompactPCI interface 4MB integrated memory provides eye-opening standard, the CPV5300 supports a 32-bit PCI 2D accelerated graphics performance for interface on the J1 physical CompactPCI human-machine interfaces and imaging connector. On-card devices connect directly to applications. Resolutions up to 1280 x 1024 the local bus. Off-card CompactPCI bus are supported. accesses are supported through the Intel 21150 PCI-PCI bridge. Dual Ethernet Two Intel 82559 Ethernet controllers provide redundant Ethernet ports for monitoring and telecom applications. One or both of these controllers can be used as a diagnostic interface allowing for remote monitoring of system status (for example, voltage and temperature). Specifications SPECIFICATIONS Processor SCSI ® Single 333 MHz Pentium II processor mobile module or Controller: Adaptec AIC-7880 500 MHz Pentium III processor mobile module PCI Bus Master: Yes, with PCI burst System Bus Ethernet 333 MHz processor: 66 MHz bus Controller: Two Intel 82559 500 MHz processor: 100 MHz bus PCI Bus Master: Yes, with PCI burst Cache Graphics Level 1: 16/16KB instruction/data (Pentium II resident) Controller: CHIPS 69030 2D accelerated Level 2: 256KB (integrated) video Video Memory: 4MB integrated memory Memory Resolution: 1280 x 1024 max.; Quarter VGA 320 x 240, 320 x 200 Socket: Two 168-pin latching DIMM socket accommodates 1/2/4/8/16/32MBx72 DIMM I/O Interfaces (Front Panel and Planar) DRAM: Synchronous, 60ns, parity or ECC mode (Both registered and unbuffered memory are USB Ports: Two 4-pin USB on front panel supported, but technologies should not be Serial Ports: mixed.) Two RS-232 (16550) 9-pin Dsub on front panel Addressing Parallel Port: One bi-directional 25-pin Dsub on front panel with all IEEE 1284 Real and protected (36-bit) addressing supported protocols supported including EPP and ECP Data Path SCSI: 68-pin Dsub on front panel Ethernet: Two RJ-45 on front panel CPU/PCI bus: 64-bit/32-bit Video: 15-pin Dsub on front panel Keyboard/mouse: 6-pin mini-DIN on front panel Bus Interface (Y-cable accessory recommended) Floppy Disk: One channel (360K to 2.88MB); CompactPCI bus: PCI Specification Rev. 2.1 support for one optional ultra-thin compliant, 32-bit, 33 MHz drive, mounted on-board EIDE: Clock/Calendar Two channel/four device PCI EIDE with LBA and PIO mode 5 support; support for one, optional 2.5" hard Real-time clock with (replaceable) battery backup; drive and/or SanDisk FlashDisk, includes CMOS mounted on-board. Interrupts Note: Physical on-board support is limited to any two or three devices: floppy, EIDE HD, or FlashDisk. Additional Four CompactPCI level-sensitive interrupts, configurable devices may be attached via transition module. to any interrupt vector for Plug-and-Play compatibility Note: All ISA on-card interrupts are Plug-and-Play compliant. BIOS Features Power Requirements • BIOS in Flash EPROM 333 MHz 500 MHz • Auto-configuration or extended setup with +5V: 2.2 A max. 2.2 A max. serial/parallel ports remappable +12V: 0.9 A max. 0.9 A max. • Diskless, keyboardless and videoless operation –12V: 0.1 mA max. 0.1 mA max. • BIOS POST and Setup • System and video BIOS shadowing +3.3V: 3.0 A max. 3.0 A max. Supervisory Demonstrated MTBF Watchdog Timer: Two-level, software (based on a sample of four boards in accelerated stress programmable (17.8 ms to 291 environment) sec.); drives interrupt Mean: 107,161 hours (configurable), NMI, or system 95% Confidence: 60,570 hours reset Alarm Microcontroller CPU temperature (user Environmental (NS LM78): definable threshold alarm on selectable IRQ: 5, 7, 9, 11, NMI, Operating Nonoperating or SMI), backplane and CPU voltages, and chassis fan Temperature: 0° C to +55° C –40° C to +65° C rotation and intrusion, with Altitude: 5,000 m 15,000 m status interrogated via NMI, SMI, Humidity (NC): 5% to 90% 5% to 95% or SMBus (on J4) @ 40° C @ 40° C Reset Switch: Guarded, on front panel Vibration: 2 Gs RMS, 6 Gs RMS, Front panel LEDs: Power OK (green), disk activity 20–2000 Hz 20–2000 Hz (green), watchdog alarm (red), random random speaker output (amber), Ethernet link (green), Ethernet Electromagnetic Compatibility (EMC) activity (amber) Intended for use in systems meeting the following CPV5300CTM80 Transition Module I/O regulations: U.S.: FCC Part 15, Subpart B, Class A (non- Transition module provides backplane I/O from J4 and J5 residential) on the CPV5300. Canada: ICES-003, Class A (non-residential) On-board Headers: Speaker, reset, two 40-pin IDE, 34-pin floppy This product was tested in a representative system to the following standards: Rear Panel: USB (two 4-pin), serial (two RS- CE Mark per European EMC Directive 89/336/EEC with 232 9-pin Dsub), bi-directional Amendments; Emissions: EN55022 Class B; Immunity: parallel (25-pin Dsub), SCSI (68- EN55024 pin Dsub), Ethernet (two RJ-45), video (15-pin Dsub), keyboard/mouse (one 6-pin mini Safety DIN) All printed wiring boards (PWBs) are manufactured with a flammability rating of 94V-0 by UL recognized Mechanical manufacturers. 6U, 8HP wide (233 mm x 160 mm x 40.64 mm), including optional on-board 3.5" floppy drive and 2.5" EIDE drive; conforms to PICMG 2.0 CompactPCI (Rev. 2.1) and PCI SIG 2.1 specifications Ordering Information ORDERING INFORMATION Part Number Description Base Board Bundles All bundles include dual Ethernet, AGP graphics, EIDE, SCSI, front panel and rear I/O with the following processor options: CPV5300C-333 333 MHz Pentium II processor mobile module with 256KB on-die cache CPV5300C-500 500 MHz Pentium III processor mobile module with 256KB on-die cache Transition Module CPV5300CTM80 IEEE 1101.11 compliant 80 mm transition module Memory MEMSD-xxx 32MB to 512MB synchronous DRAM (where xxx = number of MB) Other On-Board Options CPVEIDExGHD On-board 2.5" EIDE hard disk drive (where x = size of disk in GB) CFLASHxxx On-board EIDE compliant CompactFlash memory (where xxx = number of MB) Miscellaneous CPVCABLE-2 Front panel cable kit: includes PS/2 “Y” cable for keyboard/mouse Documentation CPV5300A/IH CPV5300 Installation and Use Manual Documentation is available for on-line viewing and ordering at http://www.motorola.com/computer/literature. Motorola Computer Group NORTH AMERICA: Tempe, AZ 800-759-1107 or 602-438-5720 ASIA: Shanghai, China +86 21 5292 5693 Regional Offices EUROPE: Loughborough, UK +44 1509 634300 PACIFIC RIM: Tokyo, Japan +81 3 5424 3101 EAST MEDITERRANEAN: Tel Aviv, Israel +972 3 568 4388 ASIA/PACIFIC: Hong Kong +852 2966 3210 www.motorola.com/computer MOTOROLA and the Stylized M Logo are registered in the U.S. Patent and Trademark Office. CompactPCI and PICMG are registered trademarks of PICMG-PCI Industrial Computer Manufacturers Group, Inc. All other product or service names are the property of their respective owners. This datasheet identifies products, their specifications, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present or future availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Motorola may sell products. A prospective buyer should exercise its own independent judgement to confirm the suitability of the products for particular applications. Motorola reserves the right to make changes, without notice, to any products or information herein which will, in its sole discretion, improve reliability, function, or design. Motorola does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes Motorola's licensee, licensee's transferees, and licensee's customers and users. Availability of some of the products and services described herein may be restricted in some locations. CV530-D4 1/02 © Motorola Inc.1997, 2001, 2002