DATASHEET KEY FEATURES ® High performance processor Designed for PICMG 3.0 and The ATCA-717 blade features a ® blade with four PMC sites 3.5 AdvancedTCA compliant managed, multi-layered 16-port systems, the Motorola Gigabit Ethernet switch that 1.8 GHz Intel Pentium M ATCA-717 processor blade delivers the fl exibility required processor ® features the 1.8 GHz Intel for routing Gigabit Ethernet ® Intel E7501 server-class chipset Pentium M processor with a interfaces between the base supporting 4.3GB/s memory high MIPS/watt capability in board control processor, the bandwidth an 8U form factor. It also PMC-based processing or ® includes an Intel E7501 chip- I/O nodes, and the PICMG Up to 4GB ECC-protected set with a memory bandwidth compliant base and fabric DDR266 SDRAM of 4.3GB/s, accommodates interfaces. The ATCA-717 is Complete software operating four PMC modules for addi- available in two memory environment including OS tional processing power and/or confi gurations (2GB and 4GB) I/O, and supports 4GB ECC- and supports optional, on-board PICMG 3.0 Gigabit Ethernet protected DDR266 SDRAM. parallel and serial ATA hard base interface support drive devices; adding to the PICMG 3.1, Option 1 and 2 performance and fl exibility of fabric interface support this processor blade. Multiple hard disk drive options ™ Service Availability Forum (SA Forum) compliant HPI and AIS software interfaces Designed for NEBS and ETSI compliance The Motorola ATCA-717 processor blade is designed to operate within both the ™ ™ Motorola Centellis 3000 and Avantellis 3000 series of communications servers. The Intel Pentium M processor delivers outstanding performance and supports light I/O and/or coprocessing via PMC sites; making it ideal for implementing almost any control plane applications. ATCA-717 AdvancedTCA Processor Blade BLOCK DIAGRAME Àœ˜ÌÊ*>˜i ˜ÌiÀv>Vià ˜Ìi *i˜ÌˆÕ“Ê { >Å 1- £°nÊâ 1- , -
/
,-‡ÓÎÓ  ,-‡ÓÎÓ <œ˜iÊÎ ˜Ìi iÞLœ>À`É ˜Ìi ˜Ìi >˜Vi “œÕÃi *È{Ó Çxä£ ,>«ˆ`à * ‡8 * ‡8 ÓÝL * ÓÝL *…Þ ÓÝL >LÀˆV * {ÝL <œ˜iÊÓ ˜ÌiÀv>Vi £È‡«œÀÌ L -܈ÌV… >Ãi * ÓÝL ÓÝL ˜ÌiÀv>Vi *…Þ ÓÝL * * * <œ˜iÊ£ q{nÊ6  É STANDARD NETWORKING The ATCA-717 processor blade provides PICMG 3.0 base interface connectivity in a dual star conŢ guration using SUPPORT standard Gigabit Ethernet technology. The PICMG 3.1 fabric interface is also supported and several conŢ gurations are available depending on application bandwidth requirements. PICMG 3.1, Option 1 – Single, redundant Gigabit Ethernet pair (1.0 Gbps) PICMG 3.1, Option 2 – Dual, redundant Gigabit Ethernet pairs (2.0 Gbps) PROCESSOR COMPLEX Surrounding the Intel Pentium M processor is an array of high performance components that combine to form a powerful processor complex. FEATURES INCLUDE: Up to 4GB, ECC-protected DDR2 SDRAM. Intel E7501 server-class chipset supporting 4.3GB/s memory bandwidth 1.0MB boot ţ ash Parallel and serial ATA hard disk drive options 2 ATCA-717 SOFTWARE SUPPORT All Motorola ATCA blades can be conŢ gured with The Avantellis 3000 software package comes optional software that, when combined with the complete with: hardware, create a fully integrated and veriŢ ed telecom MontaVista CGE 4.0 platform. Two software packages are available: Platform Control Software Centellis 3000 software package ® NetPlane Core Services Avantellis 3000 software package NetPlane Core Services (NCS) is Motorola’s SA Forum The Centellis-Avantellis 3000 platforms come complete with, compliant HA middleware combined with select and are veriŢ ed with, a standard Carrier Grade Linux (CGL) complimentary services to create a complete service distribution; MontaVista CGE 4.0, the market leader in Carrier availability solution. Platform Control Software (PCS) is Grade Linux. MontaVista CGE 4.0 comes complete with all lower level software that binds the platform independent required Linux Support Packages (LSPs) to support Motorola NCS software to the speciŢ c hardware platform. These ATCA blades as well as several userland applications. software packages, combined with MontaVista CGE 4.0, provide a high availability platform ready for customer The Centellis 3000 software package comes complete with: applications – the Avantellis 3000 platform. MontaVista CGE 4.0 RELEVANT STANDARDS Basic Blade Services Open Source Development Labs (OSDL), rev. 1.0 Basic Blades Services (BBS) software is provided SA Forum to enable a set of ATCA hardware and software – Hardware Platform Interface (HPI) – rev. 1.0, A .01.01 components into a fully integrated and veriŢ ed telecom – Application Interface SpeciŢ cation (AIS) – platform – the Centellis 3000 platform. This platform is rev. 1.0, A .01.01 ready for customers HA middleware and application For more information on the Centellis and Avantellis environment. 3000 platforms, please refer to the Centellis 3000 and Avantellis 3000 series datasheets. Basic Blade Services (generic to all ATCA blades): Hardware Platform Management including local IPMC, LED, EKeying and blade extraction software Firmware upgrade utility Local management access (SNMP, CLI) INTELLIGENT PLATFORM The PICMG 3.0 AdvancedTCA standard speciŢ es a low-level, environmental management architecture referred to as MANAGEMENT CONTROL intelligent platform management interface (IPMI). The ATCA-717 blade implements this functionality using an off-the- PLATFORM MANAGEMENT shelf hardware and software based IPM controller that monitors all local, blade-speciŢ c environmental information. Management access to this information is provided through the SA Forum deŢ ned HPI interface. REAR TRANSITION MODULES Motorola offers a rear transition module (RTM) for the ATCA-717 processor blade for access to an assortment of interfaces like USB, keyboard/mouse as well as SATA storage interfaces. PMC SITE The ATCA-717 blade provides four, single width IEEE1386.1-2001 PMC sites. The PMC site supports PCI-X 64-bit 133 MHz capable PMC modules. These can be used for any combination of processor, coprocessor or I/O functions. ATCA-717 3 HARDWARE PROCESSOR EXTERNAL INTERFACES 1.8 GHz Intel Pentium M Processor Front Panel 512KB L2 on-chip cache – USB 2.0, mini USB Type AB (2) 400 MHz frontside bus – Serial, RJ-45 (2) Intel E7501 system controller – Keyboard/mouse, PS2 (1) Via Optional RTM MEMORY – USB 2.0, Type A (2); Serial, RJ-45 (2); SATA (1). – From PTMC: E1/T1, RJ-45 (16); Serial, RJ-45 (2) Up to 4GB, ECC-protected SDRAM. Supported conŢ gurations – 2GB and 4GB – Keyboard/mouse, PS2 (1) 256Byte CMOS NVRAM for BIOS conŢ guration 1.0MB boot ţ ash, single bank architecture POWER REQUIREMENTS 1.0MB backup boot ţ ash (can alternatively be used as Dual-redundant –48V rails application ţ ash) Input range: 39.5 – 72 VDC Support for CompactFlash card Typical power: 120 – 140W COUNTERS/TIMERS BLADE SIZE Real-time clock 8U form factor, 280 mm X 322.5 mm, single slot Programmable watchdog timer RELEVANT STANDARDS PCI MEZZANINE CARD PICMG 3.0 (form factor, IPMI, base interface, hot swap, Four PMC sites with 100 MHz PCI-X interface and dual RTM) Gigabit Ethernet interface PICMG 3.1, Option 1 and 2 BASE AND FABRIC INTERFACES Dual star conŢ guration PICMG 3.0 base interface compliant, Gigabit Ethernet (1.0Gbps) PICMG 3.1 fabric interface compliant, Gigabit Ethernet – PICMG 3.1, Option 1 – Single, redundant Gigabit Ethernet pair (1.0Gbps) – PICMG 3.1, Option 2 – Dual, redundant Gigabit Ethernet pairs (2.0Gbps) ORDERING INFORMATION Part Number SAP# Description ATCA processor blade with Intel Pentium M processor, PENT/ATCA-717/2G-1800 123065 2GB memory and 4 PMC slots ATCA processor blade with Intel Pentium M processor, PENT/ATCA-717/4G-1800 123066 4GB memory and 4 PMC slots 123063 RTM for the ATCA-717 blade ACC/ARTM-717 ACC/ATCA-715/HDD 120980 30GB IDE PATA HDD and mounting kit for the ATCA-717 ACC/ATCA-715/HDD-SATA 122240 60GB IDE SATA HDD and mounting kit for the ATCA-717 Provides serial interfaces (COM1 and COM3) and keyboard/mouse 122241 ACC/ATCA-CMC-MODULE on the front panel of ATCA-717, mounted in PMC site #4 122242 Adapter cable – single RJ-45 plug to dual RJ-45 sockets ACC/CABLE/PMC/RJ45 Adapter cable – mini USB B-Male to USB A-Female (needed to 121792 ACC/CABLE/USB connect e.g., a disk drive to front panel of ATCA-717) Adapter cable – RJ-45 to DSUB9 female (needed to connect e.g., a ACC/CABLE/RJ45/DSUB 121793 laptop to serial interface of ATCA-717) 4 ATCA-717 REGULATORY COMPLIANCE Item Description Designed to comply with NEBS GR-63-CORE, NEBS Physical Protection, Level 3 GR-1089-CORE, Electromagnetic Compatibility and Electrical Safety — Generic Criteria for Network Telecommunications Equipment. Level 3, Equipment Type 2 Designed to comply with ETSI ETSI Storage, ETS 300 019-1-1, Class 1.2 equipment, Not Temperature Controlled Storage Locations ETSI Transportation, ETS 300 019-1-2, Class 2.3 equipment, Public Transportation ETSI Operation, ETS 300 019-1-3, Class 3.2 equipment, Partly Temperature Controlled Locations Designed to comply with Acoustic ETS-300-753, Equipment Engineering (EE); Acoustic noise emitted by telecommunications equipment EMC EN-300-386 Electromagnetic compatibility and Radio spectrum Matters (ERM); telecommunication network equipment; ElectroMagnetic Compatibility (EMC) requirements, Environment Class 3.2, Telecommunication equipment room (attended) FCC 47 CFR Part 15 Subpart B (US), Class A EMC Directive 89/336/EEC (EU) AS/NZS 3548 (Australia/New Zealand), Limits and Methods of Measurement of Radio Disturbance Characteristics of Information Technology Equipment VCCI Class A (Japan), Voluntary Control Council for Interference by Information Technology Equipment Safety UL60950 (US CSA Mark), CSA22.2 No.60950 (Canada CSA Mark), EN60950 (EU VDE Mark), IEC60950 (Intl. CB Scheme) Safety of information technology equipment, including electrical business equipment ETS 300-132-2 Environmental Engineering (EE); Power supply interface at the input to telecommunications equipment; Part 2: Operated by direct current (dc) RoHS Status This product is being redesigned for RoHS compliance. The part number for the RoHS compliant product is ATCA-7107. SOLUTION SERVICES Motorola provides a portfolio of solution services optimized to meet your needs throughout the product lifecycle. Design services help speed time-to-market. Deployment services include global 24x7 technical support. Renewal services enable product longevity and technology refresh. And solution extras include enhanced warranty and repairs. Sales OfŢ ces Tempe, AZ U.S.A. 1 800 759 1107 or +1 602 438 5720 Tel Aviv, Israel +972 3 568 4385 Paris, France +33 1 69 35 25 88 Shanghai, China +86 215292 5693 Munich, Germany +49 89 608 14-0 Tokyo, Japan +81 3 5424 3101 Loughborough, UK +44 1509 634300 Hong Kong, China +852 2966 3209 This document identifi es products, their specifi cations, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present or future availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Motorola may sell products. A prospective buyer should exercise its own independent judgment to confi rm the suitability of the products for particular applications. Motorola reserves the right to make changes, without notice, to any products or information herein which will, in its sole discretion, improve reliability, function, or design. Motorola does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes Motorola’s licensee, licensee’s transferees, and licensee’s customers and users. Availability of some of the products and services described herein may be restricted in some locations. www.motorola.com/computing MOTOROLA and the Stylized M Logo are registered in the U.S. Patent and Trademark Offi ce. PICMG, AdvancedTCA and the AdvancedTCA logo are registered trademarks of the PCI Industrial Computer Manufacturers Group. Service Availability is a proprietary trademark used under license. Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. All other product or service names are the property of their respective owners. © Motorola, Inc. 2006 ATCA717-D1 05/06