M36 Data Sheet - 2006-07-20 M36 - 8/16 Analog Inputs n 8/16 current or voltage inputs n 16 bits resolution n 10 µs acquisition/conversion time n Unipolar/bipolar software-selectable n Auto-sampling system n Communication via dual-ported RAM n External triggering n Optical isolation n On-board signal conditioning with SA-Adapter™ The M36 is a 16-bit analog input M-Module™. The The M36 is based on the M-Module™ ANSI mezzanine isolated supply voltages can be generated by an on-standard. It can be used as an I/O extension in any board DC/DC converter. Sampling on the M-Module™ is type of bus system, i.e. CPCI, PXI™, VME or on any completely automatic. The measured values are type of stand-alone SBC. Appropriate M-Module™ carrier available in a dual-ported RAM. The sequence and mode cards in 3U, 6U and other formats are available from of channels to be measured can also be defined in the MEN or other manufacturers. dual-ported RAM. Acquisition time is less than 10µs. Input signal conditioning is done using a small adapter. ® 1 Embedded Solutions M36 Data Sheet - 2006-07-20 Technical Data A/D Conversion Peripheral Connections n 16 bits @ 10µsn Via front panel on a shielded 25-pin D-Sub receptacle n Precision: ±2 LSB, ±0.1% typ.connector n Noise: ±3 LSB of mean value, delta = 0.8n Via carrier board (rear I/O) n Optically isolated (500V isolation) n Programmable gain factor of 1, 2, 4 or 8 (factor 16 by M-Module™ Characteristics hardware jumpering)n A08, D16, INTA, IDENT n Offset max. 4 LSB (25°C) n Full-scale error max. 4 LSB (25°C)Electrical Specifications n Software-selectable unipolar or bipolar operationn Isolation voltage: n Sample and holdo 500V DC between isolated side and digital side n Autoincrement of channel numbero 180V DC between the channels o Voltage between the connector shield and isolated Input Signal Conditioning with AD01ground is limited to 180V using a varistor; AC n Voltage or Current Inputscoupling between connector shield and isolated ground o 16 analog inputs, single-endedthrough 47nF capacitor o High input voltage tolerance n Supply voltages/power consumption: o Cross-talk less than 56dbo +5V (4.85V..5.25V), 110mA typ. (without DC/DC o Low-pass filter 1kHzconverter), 580mA (with DC/DC), 990mA (with DC/DC and n Voltage MeasurementAD01) o Precision: ±0.5%o External supply voltages (without on-board DC/DC o Voltage max.: ±15Vconverter and adapter): +15V: 14.5V..15.5V, +60mA; o Voltage full scale: ±10V-15V: 14.5V..15.5V, -32mA o Input resistance: 100 kOhm, ±10% n MTBF: 312,000h @ 50°C (derived from MIL-HDBK-217F) n Current Measurement o Precision: ±1%Mechanical Specifications o Current max.: ±25mAn Dimensions: conforming to M-Module™ Standard o Current full scale: ±20mA, UA = ±1.25Vn Weight (incl. adapter): 102g o Load resistance: 62.5 Ohm, ±0.1% Environmental Specifications Input Signal Conditioning with AD02n Temperature range (operation): n Voltage or Current Inputso 0..+60°C o 8 analog inputs, differentialo Industrial temperature range on request o High common mode range ±200Vo Airflow: min. 10m³/h o Cross-talk less than 60db n Temperature range (storage): -40..+85°C o Low-pass filter 3kHzn Relative humidity range (operation): max. 95% n Voltage Measurementnon-condensing o Precision: ±0.5%n Relative humidity range (storage): max. 95% non-condensing o Voltage max.: ±200V (common mode)n Altitude: -300m to + 3,000m o Voltage full scale: ±10Vn Shock: 15g/11ms o Input resistance: 400 kOhm typ.n Bump: 10g/16ms n Current Measurementn Vibration (sinusoidal): 2g/10..150Hz o Precision: ±1%n Conformal coating on request o Current max.: ±25mA o Voltage max. to IGND: ±200VSafety o Input resistance: 62.5 Ohm, ±0.1%n PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers Miscellaneous n External trigger (isolated, rising-edge sensitive)EMC n External binary inputn Tested according to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and IEC1000-4-4 (burst) with regard to CE conformity ® 2 Embedded Solutions M36 Data Sheet - 2006-07-20 Technical Data Software Support n MEN Driver Interface System (MDIS™ for Windows®, Linux, VxWorks®, QNX®, RTX, OS-9®) ® 3 Embedded Solutions M36 Data Sheet - 2006-07-20 Diagram ® 4 Embedded Solutions M36 Data Sheet - 2006-07-20 Ordering Information Miscellaneous 05M000-00 M-Module™ cable, 2m, with 25-pin D-Sub plug/housing to pig tail 05M000-17 25 mounting screw sets to fix M-Modules™ on carrier boards 08AD01-01 Adapter for M34/M35/M36: 16 voltage inputs, single-ended, discontinued as of December 19, 2005 08AD01-02 Adapter for M34/M35/M36: 16 current inputs, single-ended, discontinued as of December 19, 2005 08AD01-04 Adapter for M34/M35/M36: 16 current inputs, single-ended, temperature range: -40..+85°C, discontinued as of December 19, 2005 08AD02-01 Adapter for M34/M35/M36: 8 voltage inputs, differential, discontinued as of December 19, 2005 08AD02-02 Adapter for M34/M35/M36: 8 current inputs, differential, discontinued as of December 19, 2005 08AD32-00 Adapter for M34/35/36 and M67: evaluation card Software: OS independent 13M036-06 MDIS4™/2004 low-level driver sources for M36 Software: Windows 13M036-70 MDIS4™/2004 Windows® NT4/W2K/XP and XP Embedded driver for M36 Documentation 20M000-00 M-Module™ draft specification, Rev. 3.0 20M036-00 M36 user manual For the most up-to-date ordering information and direct links to other data sheets and downloads, see the M36 online data sheet under » www.men.de. ® 5 Embedded Solutions M36 Data Sheet - 2006-07-20 Contact Information Germany France USA MEN Mikro Elektronik GmbHMEN Mikro Elektronik SAMEN Micro, Inc. Neuwieder Straße 5-718, rue René CassinPO Box 4160 90411 NurembergZA de la ChâtelaineLago Vista, TX 78645-4160 Phone +49-911-99 33 5-074240 GaillardPhone (512) 267-8883 Fax +49-911-99 33 5-901Phone +33 (0) 450-955-312Fax (512) 267-8803 E-mail info@men.deFax +33 (0) 450-955-211E-mail sales@menmicro.com www.men.deE-mail info@men-france.frwww.menmicro.com www.men-france.fr The date of issue stated in this data sheet refers to the Technical Data only. Changes in ordering information given herein do not affect the date of issue. All brand or product names are trademarks or registered trademarks of their respective holders. Information in this document has been carefully checked and is believed to be accurate as of the date of publication; however, no responsibility is assumed for inaccuracies. MEN Mikro Elektronik accepts no liability for consequential or incidental damages arising from the use of its products and reserves the right to make changes on the products herein without notice to improve reliability, function or design. MEN Mikro Elektronik does not assume any liability arising out of the application or use of the products described in this document. The products of MEN Mikro Elektronik are not suited for use in nuclear reactors and for application in medical appliances used for therapeutical purposes. Application of MEN's products in such plants is only possible after the user has precisely specified the operation environment and after MEN Mikro Elektronik has consequently adapted and released the product. Copyright © 2006 MEN Mikro Elektronik GmbH. All rights reserved. ® 6 6 Embedded Solutions