Product Specifications IDE 3000 2.5” Flash Disk Solid State IDE Drive Highlights M-Systems’ IDE 3000 2.5” is a solid-state IDE drive family based on nonvolatile NAND flash technology. The IDE 3000 2.5” family is a rugged flash disk solution designed as a drop-in replacement for mechanical HDDs when high reliability is a primary concern. Scope This product specification defines the performance, design, manufacturing and acceptance requirements of the IDE 3000 2.5” flash disk. Features The IDE 3000 2.5” drive family offers the following benefits: Capacities ranging from 16MB to 1GB � � Solid state: no moving parts � 2.5" form factor with a height of 6 mm/0.25" � Interface transfer rate of 16.6MB/s (PIO mode 4) � Low power consumption (0.05W to 0.9W) � MTBF 1,000,000 Power-on hours (typical) � ATA compliance 1 Rev. 1.0 49-SR-003-01-6L IDE 3000 2.5” Flash Disk Table of Contents 1. Specifications ...................................................................................................................................... 3 1.1 Critical Item Definition ................................................................................................................. 3 1.1.1 Interface Definition ....................................................................................................................................3 1.2 Characteristics ............................................................................................................................ 3 1.2.1 IDE Transfer Modes ..................................................................................................................................3 1.2.2 Performance..............................................................................................................................................3 1.2.3 Access Time..............................................................................................................................................3 1.2.4 Seek Time .................................................................................................................................................3 1.2.5 Current Consumption ................................................................................................................................4 1.2.6 Memory Capacity ......................................................................................................................................4 1.2.7 Endurance .................................................................................................................................................4 1.2.8 Physical Characteristics ............................................................................................................................5 1.3 Environmental Conditions ........................................................................................................... 7 1.3.1 Temperature..............................................................................................................................................7 1.3.2 Altitude.......................................................................................................................................................8 1.3.3 Relative Humidity ......................................................................................................................................8 1.3.4 Shock.........................................................................................................................................................8 1.3.5 Vibration ....................................................................................................................................................8 1.3.6 Storage Life ...............................................................................................................................................8 2. IDE 3000 2.5” Drive Configuration..................................................................................................... 9 3. Interface Connectors ........................................................................................................................ 10 4. Supported IDE Commands...............................................................................................................11 5. CE and FCC Compatibility................................................................................................................12 6. Label Information ..............................................................................................................................12 7. Ordering Information ........................................................................................................................ 12 2 Rev. 1.0 49-SR-003-01-6L IDE 3000 2.5” Flash Disk 1. Specifications 1.1 Critical Item Definition The dimensions of the IDE 3000 2.5” flash disk enable mounting it in a standard 2.5” disk drive bay. 1.1.1 Interface Definition The IDE 3000 2.5” drive family supports the full range of commands listed in Section 4, in compliance with ATA4 standards. 1.2 Characteristics 1.2.1 IDE Transfer Modes The IDE 3000 2.5” flash disk supports the following transfer modes: • PIO modes 0 through 4 1.2.2 Performance The IDE 3000 2.5” complies with the performance requirements, as illustrated in Table 1. Table 1: IDE 3000 2.5” Maximum Transfer Rates Host Interface Operation Sustained Rate (MB/sec) Maximum Transfer Rate (MB/sec) Read 8 2.4 Write 8 2.4 Performance was measured on a computer with the following configuration: • Pentium 133 processor • DOS • IDE Transfer Mode: PIO mode 4 To measure IDE 3000 2.5” performance, an IDE bus monitor was attached to the IDE bus. The read and write operations were recorded, and performance was calculated offline according to the following formula: Number_of_blocks _×_sector_size Write/Read_rate = Command_complete_time _-_selection_time 1.2.3 Access Time Standby to active (typical.): 2.5 msec 1.2.4 Seek Time Maximum track-to-track seek time: <0.1 msec 3 Rev. 1.0 49-SR-003-01-6L IDE 3000 2.5” Flash Disk 1.2.5 Current Consumption The current consumption is measured at input voltage of +5 VDC, with a tolerance of ±10%. Table 2: IDE 3000 2.5” Input Current Consumption Function Current (max) mA DC Read 55 Write 55 Sleep/Standby N/A 1.2.6 Memory Capacity Table 3 describes the different densities of the IDE 3000 2.5”, along with internal data storage specifications. Table 3: IDE 3000 2.5” Flash Disk Capacities Unformatted Disk Formatted Disk Capacity Cylinders Heads Sector/Cylinder Bytes/Sector Capacity (MB) (number of sectors) 16 31,104 243 4 32 512 32 62,336 487 4 32 512 48 94,080 735 4 32 512 64 125,184 978 4 32 512 80 156,160 610 8 32 512 96 187,904 734 8 32 512 128 250,368 978 8 32 512 192 377,856 738 16 32 512 256 503,808 984 16 32 512 320 628,992 624 16 63 512 384 754,992 749 16 63 512 512 1,001,952 994 16 63 512 640 1,258,992 1249 16 63 512 768 1,510,992 1499 16 63 512 896 1,762,992 1749 16 63 512 1024 2,014,992 1999 16 63 512 1.2.7 Endurance The IDE 3000 2.5” can typically undergo 1 million erase and program cycles, and an unlimited number of read cycles over the entire media. 4 Rev. 1.0 49-SR-003-01-6L IDE 3000 2.5” Flash Disk 1.2.8 Physical Characteristics Weight The weight of the IDE 3000 2.5” complies with the values defined in Table 4. Table 4: IDE 3000 2.5” Assembly Weight Memory Capacity 2.5” Maximum Weight in g/oz 1024MB 78/2.753 Dimensions Table 5 describes the nominal dimensions of the IDE 3000 2.5”. Refer to Figure 1 for detailed mounting configuration dimensions. Table 5: 2.5” Nominal Dimensions Dimensions IDE 3000 2.5” Height 0.25 in 6 mm Width 2.75 in 69.85 mm Depth 3.945 in 100.20 mm Figure 1: IDE 3000 2.5” Assembly 5 Rev. 1.0 49-SR-003-01-6L IDE 3000 2.5” Flash Disk Connector Interface The pinout for the IDE 3000 2.5” interface connector is detailed in Table 6, Table 7 and Figure 2. Table 6: J1 Pin Assignment Pin Number Signal Name Pin Number Signal Name 1 RESET- 2 GND 3 HD7 4 HD8 5 HD6 6 HD9 7 HD5 8 HD10 9 HD4 10 HD11 11 HD3 12 HD12 13 HD2 14 HD13 15 HD1 16 HD14 17 HD0 18 HD15 19 GND 20 KEY 21 N.C. 22 GND 23 HIOW- 24 GND 25 HIOR- 26 GND 27 IORDY 28 CSEL 29 N.C. 30 GND 31 INTRQ 32 IOCS16- 33 HA1 34 PDIAG- 35 HA0 36 HA2 37 CS0- 38 CS1- 39 DASP- 40 GND 41 VCC 42 VCC 43 GND 44 RSVD Table 7: J2 Pin Assignment for 2.5” Format Pin Number Signal Name Pin Number Signal Name 47 Master/Slave 48 Master/Slave 49 Master/Slave 50 Master/Slave 6 Rev. 1.0 49-SR-003-01-6L IDE 3000 2.5” Flash Disk Figure 2: IDE 3000 2.5” Pin Configuration 1.3 Environmental Conditions The IDE 3000 2.5” meets the performance requirements specified below, after exposure to non-operating environmental conditions, or during and after exposure to operating environmental conditions. 1.3.1 Temperature Operating The IDE 3000 2.5” operates without degradation at a pressure of 1 atm over the following ambient temperature range: • Commercial temperature version: 0°C to +70°C • Extended temperature version: -40°C to +85°C The maximum temperature change rate shall not exceed 5°C per minute. Non-Operating The IDE 3000 2.5” commercial temperature version meets the performance requirements specified in this document after having been tested via exposure to a nominal ambient temperature of -40°C for not less than 3 days, and +85°C for a period of not less than 6 hours. The maximum temperature change rate shall not exceed 5°C per minute. Airflow Requirements General airflow guideline: 3-5 cu.feet/min. 7 Rev. 1.0 49-SR-003-01-6L IDE 3000 2.5” Flash Disk 1.3.2 Altitude The IDE 3000 2.5” sustains full operation at altitudes ranging from sea level to 50,000 feet above sea level. It is also capable of full operation during air transportation via non-pressurized flights at altitudes greater than 50,000 feet above sea level. 1.3.3 Relative Humidity The IDE 3000 2.5” withstands conditions of 8% to 95% non-condensing relative humidity (operation and non-operation). 1.3.4 Shock The IDE 3000 2.5” sustains full operation after being subjected to 1000 G shock testing in the vertical axis. 1.3.5 Vibration The IDE 3000 2.5” remains operable without degradation when subjected to 15 G vibration testing. 1.3.6 Storage Life The IDE 3000 2.5” can be placed in non-operational storage, in shipping containers or crates, for a period of up to 3 years without its capabilities being permanently affected. 8 Rev. 1.0 49-SR-003-01-6L IDE 3000 2.5” Flash Disk 2. IDE 3000 2.5” Drive Configuration The IDE 3000 2.5” must be configured as shown in Figure 3 before being mounted in the system’s drive bay. Figure 3: IDE 3000 2.5” Disk Address Setting by Jumper 9 Rev. 1.0 49-SR-003-01-6L IDE 3000 2.5” Flash Disk 3. Interface Connectors The IDE 3000 2.5” has a 2-mm pitch interface connector located on the rear panel. It accesses the DC power source and the IDE bus through a non-shielded 44-pin flat cable. Figure 4 provides an example of a connector that can be used to interface with this connector, but any compatible connectors may be used. Figure 4: IDE 3000 2.5” Interface Connector In order to prevent damage to the disk by connecting the cable with a 180º rotation, ensure that the special plastic key at pin 20 mating connector is blocked, as shown in Figure 4. This key should be ordered from the connector manufacturer. IDE Cable The cable length should not exceed 18 in. 10 Rev. 1.0 49-SR-003-01-6L IDE 3000 2.5” Flash Disk 4. Supported IDE Commands The IDE 3000 2.5” supports the commands listed in Table 8. Table 8: IDE Commands Command Name Command Code CHECK POWER MODE 98h E5h EXECUTE DEVICE DIAGNOSTIC 90h FORMAT TRACK 50h IDENTIFY DEVICE Ech IDLE 97h E3h IDLE IMMEDIATE 95h E1h INITIALIZE DEVICE PARAMETERS 91h READ BUFFER E4h READ MULTIPLE C4h READ SECTOR(S) (with retry) 20h READ SECTOR(S) (without retry) 21h READ LONG 22h 23h READ VERIFY SECTOR(S) (with retry) 40h READ VERIFY SECTOR(S) (without retry) 41h RECALIBRATE 10h SECURITY DISABLE PASSWORD F6h SEEK 70h SET FEATURES Efh SET MULTIPLE MODE C6h SLEEP 99h E6h STANDBY 96h E2h STANDBY IMMEDIATE 94h E0h WRITE BUFFER E8h WRITE MULTIPLE C5h WRITE SECTOR(S) (with retry) 30h WRITE SECTOR(S) (without retry) 31h WRITE LONG 32h 33h NOP FFh 11 Rev. 1.0 49-SR-003-01-6L IDE 3000 2.5” Flash Disk 5. CE and FCC Compatibility The IDE 3000 2.5” conforms to CE requirements, and FCC standards. 6. Label Information The outside label contains the following information (see Figure 5): 1. M-Systems logo in the lower left corner 2. Unformatted-capacity value in the center 3. Declaration (Made In Israel) along the right edge 4. CE and FCC logos in the upper left corner 5. Ordering Info (written ordering info will be printed in the upper right corner after production) 6. Part number (written number and bar code to be printed in the upper right corner after production) 7. Serial number, including date code (written number and bar code to be printed in the upper right corner after production) 8. ESD warning logo and statement in the lower right corner Figure 5: Outside Label 7. Ordering Information Ordering Information: IDE-25-CCCC-S-T Where: CCCC: Capacity (MB) 16, 32, 64, 80, 96, 128, 192, 256, 320, 384, 512, 640, 768, 896, and 1024 S: Revision T: Temperature Range Blank Commercial: 0°C to +70°C X Extended: -40°C to +85°C 12 Rev. 1.0 49-SR-003-01-6L IDE 3000 2.5” Flash Disk How to Contact Us http://www.m-sys.com Website: info@m-sys.com General Information: Technical Information: techsupport@m-sys.com USA China M-Systems Inc. M-Systems China Ltd. 8371 Central Ave, Suite A 25A International Business Commercial Bldg. Newark CA 94560 Nanhu Rd., Lou Hu District Phone: +1-510-494-2090 Shenzhen, China 518001 Fax: +1-510-494-5545 Phone: +86-755-519-4732 Fax: +86-755-519-4729 Taiwan M-Systems Asia, Ltd. Europe and Israel Room B, 13 F, No. 133 Sec. 3 M-Systems Flash Disk Pioneers Ltd. Min Sheng East Road 7 Atir Yeda St. Taipei, Taiwan R.O.C. Kfar Saba 44425, Israel Phone: +886-2-8770-6226 Phone: +972-9-764-5000 Fax: +886-2-8770-6295 Fax: +972-3-548-8666 Japan M-Systems Japan Inc. Arakyu Bldg., 5F 2-19-2 Nishi-Gotanda Shinagawa-ku Tokyo 141-0031 Phone: +81-3-5437-5739 Fax: +81-3-5437-5759 © 2002 M-Systems Flash Disk Pioneers, Ltd. All rights reserved. This document is for information use only and is subject to change without prior notice. M-Systems Flash Disk Pioneers Ltd. assumes no responsibility for any errors that may appear in this document. No part of this document may be reproduced, transmitted, transcribed, stored in a retrievable manner or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without prior written consent of M-Systems. M-Systems products are not warranted to operate without failure. Accordingly, in any use of the Product in life support systems or other applications where failure could cause injury or loss of life, the Product should only be incorporated in systems designed with appropriate and sufficient redundancy or backup features. Contact your local M-Systems sales office or distributor, or visit our website at www.m-sys.com to obtain the latest specifications before placing your order. ® ® ® TM TM TM DiskOnChip , DiskOnChip Millennium , and TrueFFS are registered trademarks of M-Systems. FFD , DiskOnKey and SuperMAP are trademarks of M-Systems. Other product names mentioned in this document may be trademarks or registered trademarks of their respective owners and are hereby acknowledged. 13 Rev. 1.0 49-SR-003-01-6L