KONTRON CP6003-SA
Specifications
Form Factor
PICMG
Altitude
50,000 ft (15,240 m)
Battery Input
1 Rear I/O
Climatic Humidity
93% RH at 40°C, non condensing (acc. to IEC 60068-2-78)
Compliancy
CompactPCI Core Specifi cation PICMG 2.0 Rev. 3.0, CompactPCI Hot Swap Specification PICMG 2.1 R2.0, CompactPCI System Management PICMG 2.9 R1.0, CompactPCI Packet Switching Backplane PICMG 2.16 R1.0, Designed to meet or exceed: Safety: UL 1950, UL 94, CSA 22.2 No 950, EN 60950, IEC 950, EN 55022 / EN 55024, EN 50081-1 / EN 6100-6-2
Dimensions
233 x 160 x 20.5 mm, 6U, 4HP
DVI/HDMI
2 Rear I/O
Ethernet
3 Front I/O, 2 Rear I/O
FAN control
2 Rear I/O
Flash BIOS
Two redundant 8 MByte SPI Flashes
Front Panel Gigabit Ethernet
Three 1000BASE-T Ethernet on the FP
Front Panel LEDs
Eight bicolor (red and green) control and status LEDs, Two IPMI LEDs, One Watchdog and one thermal LED, Four GP LEDs, One blue hot Swap LED
Front Panel Micro Switch
For Hot Swap
Front Panel Reset button
One reset button
Front Panel Serial Port
One RS232 interface on RJ45 connector
Front Panel USB interface
Two USB 2.0 ports, 4-pin standard USB host
Front Panel VGA
One 15-Pin D-Sub connector for analog monitors
HDAudio
1 Rear I/O
IPMI
IPMI 1.5-compliant for IPMI based management and CompactPCI System Management PICMG 2.9 R1.0
MTBF
188089 h acc. MIL-HDBK-217 FN2 Ground Benign 30°, 218585 h acc. Bellcore Issue 6 Ground Benign 30°
NAND Flash
1 Onboard Connector
Up to 32 GB NAND Flash Module option (SSD)
Onboard CPCI Bus
PICMG 2.0 Rev. 3.0 compatible, 64-bit / 66 MHz, Universal V(I/O) 5V or 3.3V signalling, Operating in system slot as system master and in peripheral slot in PCI passive mode (no communication to CompactPCI bus)
Onboard Gigabit Ethernet
Two PICMG 2.16 rear I/O 1000BASE-T ports
Onboard NAND Flash
One port available for mounting an optional NAND Flash module
Onboard PMC/XMC
One 64-bit / 133 MHz PMC slot, Pn1-Pn4, rear I/O Pn3 to J4, 3.3 volt V(I/O), Alternatively one XMC slot via P15, supporting XMC.3 x8 PCIExpress
Onboard SATA
Four ports fixed to rear I/O, One port routed to a standard SATA connector, One port available for mounting an optional 2.5” HDD or SSD
Onboard Serial Ports
COM1 (RS232) routed to front panel and rear I/O, COM2 (RS422) routed to rear I/O only
Operating temp.
0°C to +60°C, passive module heat sink, requires forced airflow cooling, extended with low voltage processor on request
Platform Controller Hub
Intel QM67
PMC / XMC
1/1 Onboard Connector
Power Consumption
Maximum: up to 60 watts (quad core), 50 watts (dual core) or less, depending on CPU type
Processor
Intel Core i7
Intel Core i7/i5 Processor Second Generation (32 nm manufacturing process)
SATA
4 Rear I/O, 2 Onboard Connector
Seria1
1 Front I/O, 2 Rear I/O
SMB
1 Rear I/O Optional
Software Support
AMI EFI (BIOS) with POST codes, setup console redirection to serial port (VT100 mode) with CMOS setup access, BIOS parameters saved in EEPROM, diskless, keyboardless, videoless operation, LAN boot support, Board identification number accessible via EEPROM, Support for Windows 7, XP, XP Embedded, Windows Server 2008R2, Linux (other OSs may be possible, please contact us for information)
Storage temp.
- 55°C to + 85°C (without battery or HDD)
Supervisory Functions, Clock/Calendar
Watchdog, software confi gurable, 125 msec to 256 sec, generates IRQ or hardware reset., Hardware monitor for thermal control, fan speed, and all onboard voltages, RTC battery backup
System Memory
Dual channel DDR3 memory with ECC and data speed of up to 1600 MHz per channel, and up to 16 GB on two SODIMM sockets
TPM
Optional Trusted Platform Module (TPM) 1.2 for enhanced hardware and software based data and system security
USB 2.0
2 Front I/O, 4 Rear I/O
Video CRT VGA
Front I/O
Weight
900g
Features
- 4HP, single slot quad or dual core CPU with passive cooling
- 5x GigEthernet Interfaces via PCIExpress
- Latest IO technology with SATA Gen 3, RAID, SSD
- Rear I/O supporting PICMG 2.16
- Scalable processor speed, Intel Core i7 / i5 up to 2.5 GHz
- Up to 16GB DDR3 1333 MHz memory with ECC via two SO-DIMM sockets
- XMC/PMC + onboard HDD + SSD Flash configuration possible
Datasheet
Extracted Text
» CP6003-SA « Intel® Core™ i7 Second Generation CompactPCI® Processor Blade » Dual- and Quad-Core Performance: Second Generation Intel® Core™ i7 processor with up to 16 GByte DDR3 memory including ECC support » Power Saving: Latest 32nm Technology for low power budgets » Highest Versatility and Excellent Power Management: Comprehensive I/O capabilities: PCIe, GigEthernet, PMC/XMC, USB, VGA, SATA RAID, SATA NAND Flash … » Broad Software Support: Complete Board Support Packages for On Board Hardware and Toolchain The pulse of innovation Kontron Datasheet CP6003-SA Intel® Core™ i7/i5 Second Generation CompactPCI® Processor Blade Benefi t from the latest technology that achieves highest processor The Intel® QM67 Platform Controller Hub provides advanced I/O technology performance at optimized power consumption. including USB 2.0 and several Serial ATA channels. Five independent Gigabit Ethernet ports (3x ports at the front and 2x for full PICMG 2.16 The power of up to four cores / eight threads enables virtualization support) provide comprehensive connectivity capabilities, enabling and multithreading applications to run in full 64-bit mode using innovative applications today by offering enough room for the emerging Enhanced Intel® Virtualization, Intel® HD Graphics, and Intel® Turbo next generation requirements. Highly versatile, the CP6003-SA can be used Boost Technology. in a system or peripheral slot. A rich set of LEDs at the front panel for debug and diagnostic, as well as full rear I/O connectivity completes the Greater Performance / Watt CP6003-SA. Compared to previous processor designs the 32nm quad-core Sandy Bridge technology allows much better performance at similar power consumption. Longterm Availability The PICMG 2.16-compliant Kontron CP6003-SA offers up to 16GB dual- Delivering a stable product based on Intel®‘s embedded product line, channel 1600 MHz DDR3 ECC memory via two SODIMM sockets, providing up the CP6003-SA ensures long term availability. This eliminates the risk to 25 GB/sec data throughput. The CP60003-SA is designed for bandwidth of unplanned design changes and unexpected expensive application intensive applications and thanks to hotswap support and IPMI (PICMG modifi cation. While minimizing deployment risks, the CP6003-SA provides a 2.9- compliant Intelligent Platform Management broad range of software support to ease the process of product integration Interface) the CPU board meets the highest demands for the management and maximize the competitive advantage of meeting the time-to-market of high-availability applications. Many of these are data and tele- window. communications applications, but also include highly sensitive, security related solutions as well as image processing systems in medical technology and other vertical industries. Unique Versatility The highly integrated CP6003-SA features a XMC site according to XMC.3 supporting x8 PCI Express (alternatively a 64-bit/133MHz PCI PMC site), an onboard 2.5- inch SATA hard disk or SSD and an industrial grade NAND Flash device - all usable in a 4HP single slot. LEDs TH/ COMA VGA 2x 1000BT 1000BT 1000BT HS IPMI WD GP RST RJ45 RJ45 RJ45 RJ45 CRT USB Front Panel RS VGA Mag. Mag. Mag. 232 Switch FRU to Rear I/O DDR3 w ECC DDR3 w ECC EEP FPGA SODIMM SODIMM IPMI GbE SIO TPM (on request) Board memory memory PHY Controller Channel A Channel B Control Flash Temp. Sense USB LPC VGA ETH DDR3 DDR3 LPC from Quad GbE Controller uEFI BIOS SPI Redundant nd Flash Intel® Debug FDI 2 gen. FDI FDI QM67 XDP Intel® DMI 2.0 EEP DMI DMI Core™ i7/i5 2 SMB I C PCIe x8 Bat. RTC SATA HDA USB 2xDP PCIe PCIe PCIe PCIe PCIe PCIe x4 to Front I/O x4 x4 2.5" PCIe PCIe SATA to to SSD/HDD site Quad GbE PCI/X PCI Controller SATA PCI / PCIX PCI Cable 64/133 MHz 64/66MHz Conn. to VGA DP to PMC/XMC Switch Hot to RS HDMI / PCI / PCIX 64/133 MHz or Mag. Mag. Swap 422 Front I/O DVI XMC PCIe x8 4x 4x 2x HDA IPMB COMA COMB VGA CRT GbE GbE PCI 64/66 MHz cPCI Rear I/O J4 SATA USB HDMI/DVI 3.3V / 5V VIO 2 www.kontron.com Kontron Datasheet Technical Information Processor Intel® Core™ i7/i5 Processor Second Generation (32 nm manufacturing process)up to 2.1 GHz quad core, up to 2.5 GHz dual core Platform Controller Hub Intel® QM67 Memory System Memory Dual channel DDR3 memory with ECC and data speed of up to 1600 MHz per channel and up to 16 GB on two SODIMM sockets NAND Flash Up to 32 GB NAND Flash Module option (SSD) Flash BIOS Two redundant 8 MByte SPI Flashes Front Panel Functions Gigabit Ethernet Three 1000BASE-T Ethernet on the FP Serial Port One RS232 interface on RJ45 connector USB interface Two USB 2.0 ports, 4-pin standard USB host VGA One 15-Pin D-Sub connector for analog monitors Reset button One reset button Micro Switch For Hot Swap LEDs Eight bicolor (red and green) control and status LEDs Two IPMI LEDs One Watchdog and one thermal LED Four GP LEDs One blue hot Swap LED Onboard Interfaces Gigabit Ethernet Two PICMG 2.16 rear I/O 1000BASE-T ports SATA Four ports fi xed to rear I/O One port routed to a standard SATA connector One port available for mounting an optional 2.5" HDD or SSD NAND Flash One port available for mounting an optional NAND Flash module Serial Ports COM1 (RS232) routed to front panel and rear I/O COM2 (RS422) routed to rear I/O only; optionally RS232 routed to rear I/O only (separate ordering code) CPCI Bus PICMG 2.0 Rev. 3.0 compatible, 64-bit / 66 MHz Universal V(I/O) 5V or 3.3V signalling Operating in system slot as system master and in peripheral slot in PCI passive mode (no communication to CompactPCI® bus) PMC/XMC One 64-bit / 133 MHz PMC slot, Pn1-Pn4, rear I/O Pn3 to J4, 3.3 volt V(I/O) Alternatively one XMC slot via P15, supporting XMC.3 x8 PCIExpress Rear I/O J3: PICMG 2.16, VGA, COM 1/2, 4x USB J4: PMC rear I/O; J5: 4x SATA, HDA, battery, fan control Supervisory Functions, Watchdog, software confi gurable, 125 msec to 256 sec, generates IRQ or hardware reset Clock/Calendar Hardware monitor for thermal control, fan speed, and all onboard voltages, RTC battery backup IPMI IPMI 1.5-compliant for IPMI based management and CompactPCI® System Management PICMG 2.9 R1.0 Optional Trusted Platform Module (TPM) 1.2 for enhanced hardware and software based data and system security TPM I/O Table Summary Front I/O Rear I/O Onboard Connector Total Description Video CRT VGA 11- 1 USB 2.0 24- 6 HDAudio -1 -1 Serial 12- 2 DVI/HDMI -2 -2 Ethernet 32- 5 SATA - 426 NAND Flash --1 1 PMC / XMC - - 1/1 1/1 FAN control -2 -2 Battery Input -1 -1 SBM - 1 optional - 1 optional 3 3 w ww ww w.k .kont ontr ron.com on.com Kontron Datasheet Technical Information (continued) Compliancy CompactPCI® Core Specifi cation PICMG 2.0 Rev. 3.0 CompactPCI® Hot Swap Specifi cation PICMG 2.1 R2.0 CompactPCI® System Management PICMG 2.9 R1.0 CompactPCI® Packet Switching Backplane PICMG 2.16 R1.0 Designed to meet or exceed: Safety: UL 1950, UL 94, CSA 22.2 No 950, EN 60950, IEC 950 EN 55022 / EN 55024, EN 50081-1 / EN 6100-6-2 MTBF 188089 h acc. MIL-HDBK-217 FN2 Ground Benign 30°C 218585 h acc. Bellcore Issue 6 Ground Benign 30°C General Dimensions 233 x 160 x 20.5 mm, 6U, 4HP Weight 775g Software Support AMI EFI (BIOS) with POST codes, setup console redirection to serial port (VT100 mode) with CMOS setup access, BIOS parameters saved in EEPROM, diskless, keyboardless, videoless operation LAN boot support Board identifi cation number accessible via EEPROM Support for Windows® 7, XP, XP Embedded, Windows® Server 2008R2, Linux® (other OSs may be possible, please contact us for information) Maximum: up to 60 watts (quad core), 50 watts (dual core) or less, depending on CPU type Power Consumption Environmental Operating temp. 0°C to +60°C, passive module heat sink, requires forced airfl ow cooling, extended with low voltage processor on request Storage temp. -55°C to + 85°C (without battery or HDD) Climatic Humidity 93% RH at 40°C, non condensing (acc. to IEC 60068-2-78) Altitude 50,000 ft (15,240 m) 4 www.kontron.com Kontron Datasheet Ordering Information Article Description CPU Boards CP6003-SA-Q2.1-4G » Quad Core 2.1 GHz, Core i7-2715QE » Standard front & rear I/O, PMC/XMC » 4GB SODIMM dual channel 1333 MHz with ECC » Temperature range 0°C to 60°C CP6003-SA-Q2.1-8G » Quad Core 2.1 GHz, Core i7-2715QE » Standard front & rear I/O, PMC/XMC » 8GB SODIMM dual channel 1333 MHz with ECC » Temperature range 0°C to 60°C CP6003-SA-2.5-4G » Dual Core 2.5 GHz, Core i5-2515E » Standard front & rear I/O, PMC/XMC » 4GB SODIMM dual channel 1333 MHz with ECC » Temperature range 0°C to 60°CC CP6003-SA-2.5-8G » Dual Core 2.5 GHz, Core i5-2515E » Standard front & rear I/O, PMC/XMC » 8GB SODIMM dual channel 1333 MHz with ECC » Temperature range 0°C to 60°C CP6003-SA-2.2-4G-E1x » Dual Core 2.2 GHz, Core i7-2655LE » Standard front & rear I/O, PMC/XMC » 4GB SODIMM dual channel 1333 MHz with ECC » Temperature range -40°C to 70°C Accessories CP6003-MK2.5 SATA Mounting kit for 2.5" SATA-HDD/SSD onboard, mounting within 4HP Flash-SATA Various SSD products / sizes avaliable (not possible, if onboard HDD / SSD used Rear Transition Modules CP-RIO6-001 4HP Rear I/O Module for CP6003 with 2x DVI-D; 2xUSB2.0; 2x GbE; headers for 2x COM, Flash, SATA, fan CP-RIO6-001-HD 4HP Rear I/O Module for CP6003 with 1x DVI-D; 2x USB2.0; 2x GbE; socket for SATA 2.5" disk; headers for 2x COM, Flash, SATA, fan CP-RIO6-001-HD-216 4HP Rear I/O Module for CP6003 with 1x DVI-D; 2x USB2.0; socket for SATA 2.5" disk; headers for 2x COM, Flash, SATA, fan 4HP Rear I/O Module for CP6003 with 1x VGA; 2x USB2.0; 2x GbE; socket for SATA 2.5" disk; CP-RIO6-001-HD-VGA headers for 2x COM, Flash, SATA, fan 4HP Rear I/O Module for CP6003 with 2x USB, 2x GbE; Audio, COM1, DVI, HDMI, Connectors for USB Flash, CP-RIO6-B 4x SATA, Fan, 0°C to 60°C CP-RIO6-B-216 4HP Rear I/O Module for CP6003 with 2x USB, Audio, COM1, DVI, HDMI, Connectors for USB Flash, 4x SATA, Fan, 0°C to 60°C, PIMG2.16 Support CP-RIO6-A 4HP Rear I/O Module for CP6003 with 2x USB, 2x GbE, Audio, COM1, VGA, Connectors for USB Flash, 4x SATA, Fan, 0°C to 60°C CP-RIO6-A216 4HP Rear I/O Module for CP6003 with 2x USB, Audio, COM1, VGA, Connectors for USB Flash, 4x SATA, Fan, 0°C to 60°C, PICMG 2.16 Support Software Support KIT-CP6003 Documentation and Windows driver kit Windows XP Embedded BSP CP6003 WXPE-BSP-CP6003 LIN-BSP-CP6003 Linux BSP CP6003 VXW-BSP-CP6003 VxWorks BSP 6.x SMP support 5 www.kontron.com Kontron Datasheet CORPORATE OFFICES Europe, Middle East & Africa North America Asia Pacifi c Lise-Meitner-Str. 3-5 14118 Stowe Drive 17 Building,Block #1, ABP. 86156 Augsburg Poway, CA 92064-7147 188 Southern West 4th Ring Road Germany USA Beijing 100070, P.R.China Tel.: + 49 (0) 821 4086-0 Tel.: + 1 888 294 4558 Tel.: + 86 10 63751188 ( ) Fax: + 49 0 821 4086 111 Fax: + 1 858 677 0898 Fax: + 86 10 83682438 sales@kontron.com info@us.kontron.com info@kontron.cn 6 www.kontron.com Datasheet – CP6003-SA #03102014WMH All data is for information purposes only and not guaranteed for legal purposes. Subject to change without notice. Information in this datasheet has been carefully checked and is believed to be accurate; however, no responsibilty is assumed for inaccurancies. All brand or product names are trademarks or registered trademarks of their respective owners.
Frequently asked questions
How does Industrial Trading differ from its competitors?

Is there a warranty for the CP6003-SA?

Which carrier will Industrial Trading use to ship my parts?

Can I buy parts from Industrial Trading if I am outside the USA?

Which payment methods does Industrial Trading accept?

What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods