Form Factor

PICMG

COM

1x RS232 UART interface on RJ45 connector

CompactPCI Bus Interface

PICMG 2.0, 32/64-bit / 66 MHz, Universal signaling, REQ/GNT for 7 slots, Operating in system slot as system master and in peripheral slot in PCI passive mode (no communication to CPCI bus)

Compliancy

CompactPCI Core Specification PICMG 2.0 Rev. 3.0, CompactPCI Hot Swap Specification PICMG 2.1 R2.0, CompactPCI Packet Switching Backplane PICMG 2.16 R1.0, Designed to meet or exceed: Safety: UL 1950, UL 94, CSA 22.2 No 950, EN 60950, IEC 950, EMI/EMC: EN 55022 / EN 55024, EN 50081-1 / EN 6100-6-2

Dimensions

233 x 160 x 20.5 mm, 6U, 4HP

Environmental

CP6002-R1: IEC 60068-2-6/29/27 (0° to 60°C, forced air cooling required), CP6002-R2: VITA 47, EAC6 (-40° to +70°C, forced air cooling required), Coating on request

Ethernet

2 x 1000/100/10 Base Ethernet on RJ45

Ethernet (Dual PMC/XMC versions with reduced front I/O)

2 Front I/O, 2 Rear I/O

I/O Hub

Intel QM57, internal graphics controller w. dual independent graphic channels (front VGA or DVI and rear dual DVI/HDMI), 6 SATA II controllers, 12 x USB 2.0 (6 used), 8 x PCIe 2.0 x1, 1 x LPC

IPMI

IPMI 1.5 compliant

LEDs

2x LAN activity (yellow) and speed (green), one blue control LED for hot swap, 2x for IPMI, 1x watchdog, 1x thermal control, 4-LED-field for BIOS POST code or general purpose

Memory

Up to 8 GByte DDR-3, 1066 MHz, with ECC, dual channel 4 or 8 GB soldered, Up to 32 GB NAND Flash module with SATA interface, CompactFlash socket (CP6002-R2: SATA flash disk only), Two redundant 8 Mbit SPI Flash, Serial EEPROM

Micro switch

For hot swap

MTBF

146178 h acc. to MIL-HDBK 217FN2, Ground Benign GB controlled at 30°C

Onboard Controller

Four Gigabit Ethernet Intel® 82574L PCI Express bus controllers: 2x front I/O, 2x rear I/O to support PICMG 2.16, Watchdog: FPGA-based, software configurable, two-stage Watchdog w. programmable timeout ranging from 125 ms to 256 s in 12 steps, RTC, IPMI Controller w. Flash and RAM; ext. 1 MB SPI Flash, 64 kbit EEPROM, Super I/O: LPC Super I/O, 2x UART, HW-Monitor, fan control, Trusted Platform Module (TPM 1.2) optional

PMC

Opening for PMC front panel

PMC/XMC

1 to 2 Front I/O, J4 Rear I/O, 1/1 or 2/2 Onboard Connector

Power Consumption

Intel Core i7 Processor (32nm): Core i7-610E, 2.53 GHz: 52W max., Core i7-620LE, 2.0 GHz: 42W max.

Processor

Intel Core i7
Intel Core i7 Processor (32nm): Core i7-610E, Dual Core, 2.53 GHz, 4 MB L2 cache, Core i7-620LE, Dual Core, 2.0 GHz, 4 MB L2 cache, (LV), 1066 MHz dual-channel DDR-3 memory controller with ECC Note: Versions incorporating other CPUs available on project request. Please contact us for further assistance.

Rear I/O via J3/J4/J5

J3: PICMG 2.16, VGA, COM 1/2, keyboard, mouse, USB 3-6, HDA, speaker, FAN sense, J4: PMC I/O, J5: SATA 1-4, DVI, HDMI

Reset

Reset button, guarded

SATA

4 Rear I/O, 2 Onboard Connector

Serial (Dual PMC/XMC versions with reduced front I/O)

1 Front I/O, 2 Rear I/O

Software Support

APTIO EFI (BIOS), Setup console redirection to serial port (VT100 mode), BIOS parameters saved in Flash device, Diskless, keyboardless, videoless operation, LAN boot support, Board identification number accessible via EEPROM, Support for Windows Server 2003, 2008, 7, XP, XP Embedded, Linux, VxWorks VMWare (others on request)

System Interconnect

Serial ports: two COM ports (transceivers onboard), COM1 as RS232 on front, COM2 as RS422 on the rear I/O interface, SATA NAND Flash: One SATA port of the QM57 is routed to a dedicated onboard connector, where SATA-NAND-Flash modules can be connected, SATA: Five Serial ATA II ports, Four ports are routed to rear I/O, One available as 2.5” onboard HDD (not for dual XMC versions), PMC: one 64-bit / 66 MHz PCI PMC slot with rear I/O support or XMC (PCIe x8) slot, 5V and 3.3V PCI signalling supported, CP6002-R1/R2-MC with 2x 64-bit / 66 MHz PCI PMC slot with rear I/O support or XMC (PCIe x8) slot

USB

2 Front I/O, 4 Rear I/O
2x 4-pin connectors

VGA

1 x 15-Pin D-Sub connector for standard analog displays

Video (Dual PMC/XMC versions with reduced front I/O)

2 Front I/O, 2 Rear I/O

Weight

R1: approx. 500g; R2: approx. 720g