➤ CP6001 ® 6U Intel® Core™2 Duo Rugged Processor Blade CompactPCI ➤ High computing and graphic performance ULV and LV Intel® Core™(2) Duo processors combined with 945 chipset ➤ Three Rugged Levels - R1, R2, R3 - for demanding application requirements High shock and vibration resistant and conduction cooled versions ➤ Comprehensive I/O capabilities 3x GbE, 4x SATA, 2x DVI, onboard HDD, Flash … If it’s embedded, it’s Kontron ® ➤ The Power of Intel® Core™2 Duo Reliable, Resistant, Robust ... Explore the power and the potential versions are available with E2 capabilities Comprehensive Versatility of two cores in one processor with on project request (extended temperature The CP6001 offers comprehensive I/O Kontron's CP6001 based on the range from -40° C to +85° C). The R1 capability with 3 x GbEthernet, 4 x SATA Intel® Core™ Duo / Core™2 Duo version is designed for standard with RAID 0/1/5/10 functionality as well processor. application requirements in air-cooled as 6 x USB 2.0, 2 x COM and VGA and/or environments. The R2 version is DVI. It can also accommodate a PMC slot or ruggedized for high shock and vibration, an onboard 2.5“ SATA HDD. With up to 8 The CP6001, a CompactPCI PICMG 2.16 air-cooled environments up to, and Gbyte of USB or 2 GByte soldered flash, compliant 6U CPU board, comes with three including VITA 47’s EAC3. The R3 version is the CP6001 enables construction of a rugged levels, making it yet another fully conduction cooled and meets the highly shock and vibration resistant addition to Kontron’s rugged PICMG 2.16 VITA 47’s ECC4 requirements. system with non-rotating, non-volatile portfolio. Based on the Intel® Core™ Duo memory. / Core™2 Duo processor and mobile The CP6001 features energy efficient chipset, the CP6001 features high embedded Intel dual core processors. With Unique Security computing and graphic performance with the 1.2 GHz Intel® Core™ Duo U2500 ULV The board provides safety and security via a low thermal power design and a processor and the Intel® Core™2 Duo a trusted platform module, (TPM) 1.2, two complete set of data, communication and L7400 LV processor, the CP6001 has redundant 8 Mbit firmware hubs (fail- multimedia interfaces. extraordinary performance-per-watt over) and IPMI (Intelligent Platform values. Based on the Intel® Mobile 945GM Management Interface) support (PICMG Maximum Ruggedization chipset with a front side bus of up to 667 2.9 R1.0). Designed to withstand even the toughest MHz and ICH7-R Southbridge, the CP6001 environmental conditions, the passively provides high graphics performance for Long-term Availability cooled CP6001 featuring up to 4 GByte of the two independent digital video outputs Delivering a stable product based on soldered RAM and 2 GByte of soldered to the rear I/O as well as HDA audio Intel’s embedded product line the CP6001 application flash comes in three rugged capabilities. ensures long-term availability. levels - defined as R1, R2 and R3. All three ➤ ➤ Front Panels Functional Block Diagram R1 Version R2 Version rear IO VGA VGA VGA ChA display 1 DDR2 SDVO to DVI DVI CPU ChB GMCH DDR2 ® Intel® Intel display 2 SDVO to DVI/HDMI DVI/HDMI ™( 82945GM Core 2) I²C EEPROM Duo 667/533 MHz SMB CMOS x4 DMI GbE 2 x GbE GbE GbE 2 x GbE 82573L C 4 x USB P USB ICH7R F GbE C Intel® R audio 82573L 82801 I rear IO HDA O N LPC 4x SATA x1 x1 PCIe B Super T 2 x USB USB rear IO PS/2 IO A C RS232 RS232 P RJ45 rear IO COM COM1 K A P RS422 N M&C rear IO LEDs COM2 L BOARD E A CONTROL PCIe PCIe L CPU to to switch 32b/66MHz N RST PCI TEMP PCI PCI E COM I²C Sensors rear IO PMC TMP I²C IPMI SEN hot swap LED I²C IPMB 1st SPI I²C BIOS IDE IPMI IPMI SATA Flash Flash EEP 2 x rear IO USB SATA SATA CF 2nd SATA Flash TPM HDD Flash BIOS Con. Module 2 x rear IO Module SATA Site Flash ➤ Specification ... three levels of ruggedization Processor I/O Table Summary ® TM Description Front I/O Rear I/O Onboard Connector Total Intel Core (2) Duo Processor (65 nm): Video 1 2 - 2 - Core Duo U2500, 1.2 GHz, 533 MHz FSB, 2 MB L2 cache, (ULV) USB 2 4 - 6 - Core2 Duo L7400, 1.5 GHz, 667 MHz FSB, 4 MB L2 cache, (LV) Serial 1 2 - 2 Note: Versions incorporating other CPUs available on project request. PS/2 Mouse/Kbd - 1 - 1 Please contact us for further assistance. Ethernet 3 2 - 3 SATA - 4 2 4 Chipset USB-Flash - - 1 1 - GMCH Intel 945GM, dual-channel DDR-2 memory controller, internal PMC 1 via J4 Pn1/Pn2/Pn4 1 graphics controller with dual independent graphic channels - I/O Hub Intel ICH7R, 4 SATA II controllers, 7 x USB 2.0 (used 6 x USB), CompactPCI Bus Interface 6 x PCI-Express x1 (used 5 x PCI-Express x1), 1 x LPC - PICMG 2.0, 32-bit / 66 MHz - Universal signaling, REQ/GNT for 7 slots Memory - Operating in system slot as system master and in peripheral slot in PCI - Up to 4 GByte DDR-2, 533/667MHz, w/o ECC, 2 channels: 2 GB soldered passive mode (no communication to CompactPCI bus) + 2 GB soldered - Up to 4 GB NAND soldered Flash with onboard CompactFlash controller Rear I/O via J3/J4/J5 - Two redundant 8 Mbit Firmware Hubs (FWH) - J3: PICMG 2.16, VGA, COM 1/2, keyboard, mouse, USB 3-6, HDA, - Serial EEPROM (24LC64) 64 kbit for storing CMOS data when operating speaker, FAN sense without battery - J4: PMC I/O - J5: SATA 1-4, DVI, HDMI Onboard Controller - Gigabit Ethernet: three Intel 82573L Gigabit Ethernet PCI Express bus IPMI controllers: - IPMI 1.5 compliant · 1x fixed to front I/O · 2x selectable between front or rear I/O to support PICMG 2.16 Compliancy - Watchdog: FPGA-based, software configurable, two-stage Watchdog - CompactPCI Core Specification PICMG 2.0 Rev. 3.0 with programmable timeout ranging from 125 ms to 256 s in 12 steps - CompactPCI Hot Swap Specification PICMG 2.1 R2.0 - RTC, integrated in ICH7R - CompactPCI System Management PICMG 2.9 R1.0 - IPMI Controller, Renesas H8S/2166 controller with on-chip 512 kB - CompactPCI Packet Switching Backplane PICMG 2.16 R1.0 Flash and 40 kB RAM; ext. 1 MB SPI Flash, 64 kbit EEPROM - Super I/O: LPC Super I/O from SMSC SCH3112I-NU, 2x UART, Designed to meet or exceed: HW-Monitor, PS2, fan control - Safety: UL 1950, UL 94, CSA 22.2 No 950, EN 60950, IEC 950 - Trusted Platform Module (TPM): Infineon SLB 9635 TT 1.2 - EMI/EMC: EN 55022 / EN 55024, EN 50081-1 / EN 6100-6-2 System Interconnect General - Serial ports: two COM ports (transceivers onboard) - Dimensions: 233 x 160 x 20.5 mm, 6U, 4HP · COM1 as RS232 COM1 on front and rear I/O - Weight: R1: 622g; R2: 740g; R3: 698g · COM2 as RS422 on the rear I/O interface - MTBF: 180,332 h acc. to MIL-HDBK 217FN2, Ground Benign GB - USB NAND Flash: One USB port of the ICH7R is routed to a dedicated controlled at 30°C onboard connector, where USB-NAND-Flash modules can be connected Software Support - SATA: Four Serial ATA II ports · Two ports are routed to rear I/O - AMI BIOS with POST codes · Two are selectable between rear I/O or onboard usage: - Setup console redirection to serial port (VT100 mode) with CMOS - One onboard SATA interface routed to a standard SATA connector setup access - One available as 2.5” onboard HDD (mutually exclusive with PMC) - BIOS parameters saved in EEPROM - PMC: one 32-bit / 66 MHz PCI PMC slot with rear I/O support, 5V and - Diskless, keyboardless, videoless operation, LAN boot support 3.3V PCI signalling supported - Board identification number accessible via EEPROM - Support for Windows® XP, XP Embedded, Linux®, VxWorks® Front Panel Functions (other OSs may be possible, please contact us for information) Ethernet: 3 x 1000/100/10 Base Ethernet on RJ45 Power Consumption VGA: 1 x 15-Pin D-Sub connector for standard analog displays COM: 1x RS232 UART interface on RJ45 connector - U2500 ULV 1.2 GHz and 1GB memory: max. 23W USB: 2x 4-pin connectors - L7400 LV 1.5 GHz and 4GB memory: max. 35 W PMC: opening for PMC front panel (R1 only) Environmental LEDs: 2x LAN activity (yellow) and speed (green) one blue control LED for hot swap - CP6001-R1: IEC 60068-2-6; IEC 60068-2-27; IEC 61131-2; 2x for IPMI, 1x watchdog, 1x thermal control (0 to 60°C, forced air cooling required) 4-LED-field for BIOS POST code or general purpose - CP6001-R2: R1 + VITA 47, class V1/EAC3; normal and extended Reset: reset button, guarded (-40 to +85°C, forced air cooling required) Micro switch: for hot swap - CP6001-R3: VITA 47, class ECC4 MIL-STD-810 Method 514 Proc 1 MIL-STD-810 Method 516 Proc 1 extended (-40 to +85°C, conduction cooling required) Higher shock and vibration levels can be achieved when installed in a ruggedized system. ➤ Ordering Information Product Description Order Number CPU Boards CP6001-R1-1.2-1G R1-Level, Intel Core Duo U2500 ULV 1.2 GHz, 1GB soldered Memory 36880 CP6001-R1-1.5-2G R1-Level, Intel Core2 Duo L7400 LV 1.5 GHz, 2GB soldered Memory 36874 CP6001-R1-1.5-4G R1-Level, Intel Core2 Duo L7400 LV 1.5 GHz, 4GB soldered Memory 37139 1) CP6001-R2-1.5-2G R2-Level, Intel Core2 Duo L7400 LV 1.5 GHz, 2GB soldered Memory 36879 1) CP6001-R2-1.2-1G-E2 R2-Level, Intel Core Duo U2500 ULV 1.2 GHz, 1GB soldered Memory, E2 (-40°C to +85°C) 1021-8796 1) CP6001-R3-1.2-1G-E2 R3-Level, Intel Core Duo U2500 ULV 1.2 GHz, 1GB soldered Memory, E2 (-40°C to +85°C) 37059 USB-Flash Modules FLASH-UDOC-2GB uDOC-Module, low Profile, 2GByte 35953 FLASH-UDOC-4GB uDOC-Module, low Profile, 4GByte 35954 FLASH-UDOC-8GB uDOC-Module, low Profile, 8GByte - Services 2) 3) CP6001-MK2.5SATA Mounting kit for 2,5” SATA-HDD onboard, mounting within 4HP 37248 Rear Transition Modules CP-CTM80-3 Various 4HP versions available 29973 CP-RIO6-001 With 2xDVI-D; 2xUSB2.0; 2xGbE; headers for 2xCOM, Flash, SATA, fan 37459 With 1xDVI-D; 2xUSB2.0; 2xGbE; socket for SATA 2.5” disk; headers for 2xCOM, Flash, SATA, fan 37460 Software Support 4) KIT-CP6001 Documentation and Windows driver kit on CD-ROM 36894 4) LIN-BSP-CP6001 Linux BSP CP6001 for Suse and RedHat 36895 VXW-BSP-CP6001 VxWorks BSP 6.6 SMP support 36896 1) No onboard HDD possible, only conduction cooled PMC. 2) Mounting kit CP6001-MK2.5SATA for -R1 version only; mutually exclusive with PMC slot usage. 3) HDD must be ordered separately. 4) Free of charge, downloadable from the Internet. Please contact your local sales representative for other configuration options. -R1 -R2 -R3 ➤➤ Corporate Offices Europe, Middle East and Africa North America Asia Pacific Kontron Modular Computers GmbH Kontron AG Kontron America Corporate Office Asia Pacific Kontron Modular Computers GmbH Oskar-von-Miller-Str. 1 14118 Stowe Drive 4F, No. 415, Ti-Ding Blvd., Sudetenstr. 7 85386 Eching/Munich Germany Poway, CA 92064-7147 Sec.2, NeiHu District D-87600 Kaufbeuren Taipei, Taiwan 114 Tel. +49 (0)8165-77 777 Tel. +1-888-294 4558 Tel. +886-2-2799-2789 Tel. +49 (0)8341 - 803 0 Fax +49 (0)8165-77 219 Fax +1-858-677 0898 Fax +886-2-2799-7399 Fax +49 (0)8341 - 803 499 sales@kontron-emea.com sales@us.kontron.com sales@kontron.com.tw sales@kontron-emea.com CP6001-0208 RG Copyright © 2008 Kontron AG. All rights reserved. All data is for information purposes only and not guaranteed for legal purposes. Information has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Kontron and the Kontron logo and all other trademarks or registered trademarks are the property of their respective owners and are recognized. Specifications are subject to change without notice.