Channel

PICMG 2.0, 32-bit / 66 MHz Universal signaling, REQ/GNT for 7 slots Operating in system slot as system master and in peripheral slot in PCI passive mode (no communication to CompactPCI bus)

Chipset

GMCH Intel 945GM, dual-channel DDR-2 memory controller, internal graphics controller with dual independent graphic channels I/O Hub Intel ICH7R, 4 SATA II controllers, 7 x USB 2.0 (used 6 x USB), 6 x PCI-Express x1 (used 5 x PCI-Express x1), 1 x LPC

Cooling

CompactPCI Core Specification PICMG 2.0 Rev. 3.0 CompactPCI Hot Swap Specification PICMG 2.1 R2.0 CompactPCI System Management PICMG 2.9 R1.0 CompactPCI Packet Switching Backplane PICMG 2.16 R1.0 Designed to meet or exceed: Safety: UL 1950, UL 94, CSA 22.2 No 950, EN 60950, IEC 950 EMI/EMC: EN 55022 / EN 55024, EN 50081-1 / EN 6100-6-2

Environment

CP6001-R1: IEC 60068-2-6; IEC 60068-2-27; IEC 61131-2; (0 to 60°C, forced air cooling required) CP6001-R2: R1 + VITA 47, class V1/EAC3; normal and extended (-40 to +85°C, forced air cooling required)CP6001-R3: VITA 47, class ECC4 MIL-STD-810 Method 514 Proc 1 MIL-STD-810 Method 516 Proc 1 extended (-40 to +85°C, conduction cooling required) Higher shock and vibration levels can be achieved when installed in a ruggedized system.

Environmental

Front I/O Rear I/O Onboard Connector Total Video: 1 2 - 2 USB: 2 4 - 6 Serial: 1 2 - 2 PS/2 Mouse/Kbd: - 1 - 1 Ethernet: 3 2 - 3 SATA: - 4 2 4 USB-Flash: - - 1 1 PMC: 1 via J4 Pn1/Pn2/Pn4 1

IrDA

IPMI 1.5 compliant

Max Data Transfer Rate

Up to 4 GByte DDR-2, 533/667MHz, w/o ECC, 2 channels: 2 GB soldered + 2 GB soldered Up to 4 GB NAND soldered Flash with onboard CompactFlash controller Two redundant 8 Mbit Firmware Hubs (FWH) Serial EEPROM (24LC64) 64 kbit for storing CMOS data when operating without battery

Max. Speed

AMI BIOS with POST codes Setup console redirection to serial port (VT100 mode) with CMOS setup access BIOS parameters saved in EEPROM Diskless, keyboardless, videoless operation, LAN boot support Board identification number accessible via EEPROM Support for Windows® XP, XP Embedded, Linux®, VxWorks®

Memory

Dimensions: 233 x 160 x 20.5 mm, 6U, 4HP Weight: R1: 622g; R2: 740g; R3: 698g MTBF: 180,332 h acc. to MIL-HDBK 217FN2, Ground Benign GB controlled at 30°C

Miscellaneous

Ethernet: 3 x 1000/100/10 Base Ethernet on RJ45 VGA: 1 x 15-Pin D-Sub connector for standard analog displays COM: 1x RS232 UART interface on RJ45 connector USB: 2x 4-pin connectors PMC: opening for PMC front panel (R1 only) LEDs: 2x LAN activity (yellow) and speed (green) one blue control LED for hot swap 2x for IPMI, 1x watchdog, 1x thermal control 4-LED-field for BIOS POST code or general purpose Reset: reset button, guarded Micro switch: for hot swap

Mode

Gigabit Ethernet: three Intel 82573L Gigabit Ethernet PCI Express bus controllers: 1x fixed to front I/O 2x selectable between front or rear I/O to support PICMG 2.16 Watchdog: FPGA-based, software configurable, two-stage Watchdog with programmable timeout ranging from 125 ms to 256 s in 12 steps RTC, integrated in ICH7R IPMI Controller, Renesas H8S/2166 controller with on-chip 512 kB Flash and 40 kB RAM; ext. 1 MB SPI Flash, 64 kbit EEPROM Super I/O: LPC Super I/O from SMSC SCH3112I-NU, 2x UART, HW-Monitor, PS2, fan control Trusted Platform Module (TPM): Infineon SLB 9635 TT 1.2

Power Requirement

U2500 ULV 1.2 GHz and 1GB memory: max. 23W L7400 LV 1.5 GHz and 4GB memory: max. 35 W

Processor

Intel Core 2 Duo
Intel® CoreTM(2) Duo Processor (65 nm): - Core Duo U2500, 1.2 GHz, 533 MHz FSB, 2 MB L2 cache, (ULV) - Core2 Duo L7400, 1.5 GHz, 667 MHz FSB, 4 MB L2 cache, (LV) Note: Versions incorporating other CPUs available on project request.

Slave Functions

Serial ports: two COM ports (transceivers onboard) COM1 as RS232 COM1 on front and rear I/O COM2 as RS422 on the rear I/O interface USB NAND Flash: One USB port of the ICH7R is routed to a dedicated onboard connector, where USB-NAND-Flash modules can be connected SATA: Four Serial ATA II ports Two ports are routed to rear I/O Two are selectable between rear I/O or onboard usage: One onboard SATA interface routed to a standard SATA connector One available as 2.5” onboard HDD (mutually exclusive with PMC) PMC: one 32-bit / 66 MHz PCI PMC slot with rear I/O support, 5V and 3.3V PCI signalling supported

Wake On LAN

J3: PICMG 2.16, VGA, COM 1/2, keyboard, mouse, USB 3-6, HDA, speaker, FAN sense J4: PMC I/O J5: SATA 1-4, DVI, HDMI