Channel

PICMG 2.0 Rev. 3.0 compatible, 32 bit/33 MHz. 5V default signaling (3.3V on request available), REQ/GNT for 7 slots Operating in system slot as system master and in peripheral slot in PCI passive mode (no communication to CompactPCI bus).

Cooling

CompactPCI Core Specification PICMG 2.0 Rev. 3.0 CompactPCI Hot Swap Specification PICMG 2.1 R2.0 CompactPCI System Management PICMG 2.9 R1.0 CompactPCI Packet Switching Backplane PICMG 2.16 R1.0 Designed to meet or exceed: Safety: UL 1950, UL 94, CSA 22.2 No 950, EN 60950, IEC 950 EMI/EMC: EN 55022 / EN 55024, EN 50081-1 / EN 6100-6-2

Environment

Operating temp.: 0 oC to +60 oC standard -40 oC to +85 oC E2 with 1.1/1.4 GHz LV Pentium M (optional) Storage temp.: -55 oC to +95 oC Climatic Humidity: non condensing 93% at 40 oC (acc. to IEC 60068-2-78) Altitude: 50,000 ft. (15,240 m)

Environmental

Front I/O Rear I/O Onboard Conector Total Video: 1 1 - 1 USB: 2 2 - 4 Serial: 1 2 - 2 PS/2 Mouse: - 1 - 1 PS/2 Keyboard: - 1 1 1 Ethernet: 2 2 - 4 ATA100: - 1 2 2 SATA150: - 2 1 2 CompactFlash: - - 1 1 PMC: 1 via J4 Pn1-Pn4 1 Floppy: - 1 - 1

I/O

Two 16C550 compatible UARTs (COM1/2) Keyboard on rear and onboard connector and mouse interface on rear Floppy disk controller on rear Four USB 2.0 interfaces with up to 480 Mbit/sec, two front, two rear Up to four 10/100/1000 MB/s Gigabit Ethernet ports based on the Intel 82546EM Ethernet 64-bit PCI bus controller. Two copper ports are routed to front and two copper ports are routed to PICMG 2.16 rear pins. VGA Video Controller integrated in Intelfi 82855GME GMCH providing 2048x1536x8bit/60Hz resolution, max. shared memory 64MB

IrDA

IPMI 1.5-compliant for IPMI based management and CompactPCI System Management PICMG 2.9 R1.0.

Max Data Transfer Rate

400MHz processor side bus, Intel 82855GME Up to 2 GB PC333 DDR SDRAM w/ or w/o ECC via two 200-pin SODIMM sockets Socket for CompactFlash Type II module Connector for onboard 2.5" HDD support 1 MB Firmware Hub (FWH) for BIOS 8 kB for storing CMOS data when operating without battery

Max. Speed

AMI BIOS with POST codes, setup console redirection to serial port (VT100 mode) with CMOS setup access, BIOS parameters saved in EEPROM, diskless, keyboardless, videoless operation LAN boot support. Board identification number accessible via EEPROM Support for Windows 2000, XP, XP Embedded, Windows Server 2003, Linux, VxWorkss

Memory

Dimensions: 233 x 160 x 20.5 mm, 6U, 4HP Weight: 350g MTBF: 139.589 h @ 30 C / 86 F (Bellcore Issue 6)

Miscellaneous

COM1: 9-pin D-Sub (RS232, RS422) VGA: 15-pin D-Sub SVGA connector Ethernet: 2x RJ-45 (depending on version) USB: 2x 4-pin connectors PMC: opening for PMC front panel LEDs: 2x LAN activity (yellow) and speed (green) one blue control LED for hot swap 2x for IPMI, 1x watchdog, 1x thermal control 8-LED-field for BIOS POST code or general purpose Reset: reset button, guarded Micro switch: for hot swap

PCI

One 64-bit / 66MHz PMC slot Pn1-Pn4, rear I/O Pn3 to J4. 3.3 V PCI voltage.

Power Mode

1.1/1.4 GHz 1.6/1.8 GHz 3.3V: 8-10 W / max. 11 W typ. 8-10 W / max. 12 W 5V: 5-7 W / max. 11 W typ. 16-18 W / max. 27 W +12V required -12V not required

Processor

Mobile low power Intel PentiumM processor in Micro-FCBGA 479-pin package 2x 32KB L1 cache and 1MByte/2MByte L2 cache, 400MHz processor system bus. low power dissipation: 1.1GHz (1 MByte L2) /1.4GHz LV (2 MByte L2) extended temperature range option high performance 1.6GHz (1 MByte L2) / 1.8GHz (2 MByte L2) All board versions are passive cooled with a heatsink within 4HP height. Forced air cooling at a specific flow rate is required depending on the processor version.

Socket

Watchdog, software configurable, 125 msec to 256 sec generates IRQ, NMI or hardware reset. Hardware monitor LM87 for thermal control, fan speed and all onboard voltages. RTC (integrated in HanceRapids) and CMOS RAM with backup, battery replaceable.

System Monitor

Two IDE connectors supporting Ultra DMA, one 40pin/2.54mm, one 44 pin/2mm for onboard 2.5 IDE HDD or Flash One SATA connection (optional), can be used alternatively to connect an onboard 2.5" SATA HDD instead of an onboard 2.5" IDE HDD CompactFlash type II socket 22-pin connector with all LPC signals PS/2 keyboard connector 2x200-pin SODIMM connectors 4x 64-pin PMC interface

Wake On LAN

J3: PICMG 2.16, VGA, COM0/1, keyboard, mouse, USB3/4 J4: PMC rear I/O J5: SATA 1/2, IDE (secondary), Floppy