Climatic Humidity

93% RH at 40°C, non-condensing (acc. to IEC 60068-2-78)

COM

1x 9-pin D-Sub connector

CompactFlash

4HP: Type I and Type II, mounting on piggy-back module, 8HP: Type I and Type II, mounting on extension via CompactFlash socket

CompactPCI Bus Interface

PICMG 2.0 Rev. 3.0 compatible, 32-bit/33MHz system master universal 5V and 3.3V PCI signalling voltage supported, 7 Req/Gnt & clock lines

Compliancy

CompactPCI Core Specification PICMG 2.0 Rev. 3.0, CompactPCI Hot Swap Specification PICMG 2.1 R2.0, Designed to meet or exceed: Safety: UL 60950-1, CSA 22.2 No 60950-1, EN60950-1, EMI/EMC: EN 55022 / EN 55024, EN 50081-1 / EN 61000-6-2, EN50155 (Conformal coating on request.)

Control

Reset button and HDD LED

Dimensions

100 x 160mm, 3U

DVI

1x 29-pin DVI-D connector

EPROM

Serial EEPROM (24LC64) 64 Kbit for CMOS data storing (no battery operation)

Ethernet

2x RJ45 with integrated LEDs (ACT, SPEED)

Flash (BIOS)

8 MBit Firmware hub (FWH)

Gigabit Ethernet

2x GbE Front or Rear (s/w switchable), 82574L PCI-Express controller

GMCH (Graphics Memory Controller Hub)

Intel® 945GSE chipset, Single-channel DDR2 memory controller, Internal graphics controller with dual, independent VGA channels

Hot Swap

Support for all signals to allow peripheral boards to be hot swapped. The individual clocks for each slot and access the backplane ENUM# signal comply with the PICMG 2.1 Hot Swap Specification

I/O Controller Hub

Intel® ICH7-M, 2x SATA I, 6x USB 2.0, 4x PCI-Express x1, 1x IDE, 1x 32-bit/33 MHz PCI master interface

I/O Extension Connector (to 8HP)

1x SATA, SDVO, 2x USB, LPC, PS/2, COM, IDE

LEDs

WD/GP: Watchdog or General Purpose, TH/GP: Overtemperature Status or General Purpose

MTBF

307,691 h acc. to MIL-HDBK-217 FN2, Ground Benign GB, controlled at 30°C

N270 1.6 GHz and 2 GB memory

typ. 10W

Operating Temp

0°C to +55ºC, passive module heatsink, convection cooling, -40°C to +80°C, passive module heatsink, forced airflow

Processor

Intel Atom
Intel Atom processor in micro-FCBGA8 package (45nm manufacturing process): N270: 1.6 GHz, 533 MHz FSB, 512 kB L2 cache

PS/2

1x 6-pin shielded mini-DIN connector

Rear I/O via J2 The CP305 supports

32-bit/33 MHz CompactPCI interface, two USB 2.0 ports, two Gigabit Ethernet ports without LED signals, two SATA ports, two COM ports (TTL level), one VGA analog port, one fan control input, one power management output

RTC

Integrated in ICH7-M

Serial ATA

2x switchable SATA I ports: 1x onboard standard SATA connector and 1x I/O extension or 2x Rear I/O

Software Support

AMI BIOS with POST codes, setup console redirection to serial port (VT100 mode) with CMOS setup access, BIOS parameters saved in EEPROM, diskless, keyboardless, LAN boot support, Board identification number accessible via EEPROM, Support for Windows® XP, XP Embedded, Linux®, VxWorks (Other OSs may also be used with the CP305. Please contact Kontron for further information.)

Storage Temp.

-55°C to +85ºC (without battery)

Super I/O

LPC Super I/O SMSC SCH3112I-NU with 2x UART, HW Monitor, PS/2

Supervisory Functions

Watchdog, software configurable, 125ms to 4096s in 16 steps, generates IRQ or hardware reset, dual-stage configuration, hardware monitoring SCH3112 for thermal control, fan-sense/control and all important onboard voltages

System Memory

Up to 2 GB 533 MHz DDR2 memory, soldered, no ECC

USB

2x USB 2.0, USB-A connectors

VGA

1x VGA-CRT 15-pin D-Sub connector
Integrated in 945GSE max. 2048 x 1536 pixels (QXGA) @75Hz, max. 265 MB memory used from system memory

Watchdog

Timeout ranging from 125ms to 4096s programmable in 16 steps, IRQ, Reset, dual-stage

Weight

4HP: 320g, 8HP: 540g