CFast

Onboard CFast mounting within 8HP mezzanine

Climatic Humidity

93% RH at 40°C, non-condensing (acc. to IEC 60068-2-78)

COM

1 x 9-pin D-Sub connector, RS-232 signalling

CompactPCI Bus Interface

PICMG 2.0 Rev. 3.0 compatible, 32-bit/33MHz, version with rear I/O via J2, Universal 5V and 3.3V PCI signalling voltage supported, 7 Req/Gnt & clock lines, Operating in system slot as system master and in peripheral slot in PCI passive mode

Compliancy

CompactPCI Core Specifi cation PICMG 2.0 Rev. 3.0, CompactPCI Hot Swap Specifi cation PICMG 2.1 Rev. 2.0, Designed to meet or exceed: Safety: UL 60950-1, CSA 22.2 No 60950, EN 60950-1, IEC 60950-1, EMI/EMC: EN 55022 / EN 55024, EN 61000-6-3 / EN 61000-6-2

Control

Reset button and HDD LED

Dimensions

100 x 160mm, 3U, 4HP or 8HP

DVI

1 x 29-pin DVI-D connector

EEPROM

Serial EEPROM (24LC64) 64 Kbit for storing uEFI BIOS settings and serial number

Ethernet

2 x RJ45 with integrated LEDs (ACT, SPEED)

Flash (uEFI)

2 x redundant 8 MB SPI Flashes, with fail-over functionality

Gigabit Ethernet

2 x GbE, front or rear (switchable), Intel 82574L Ethernet controller, WOL (Wake-On-LAN) support

HDD

Onboard 2.5“ SATA HDD mounting within 8HP mezzanine

High-Speed I/O Connector

The high-speed I/O connector to the extension module holds the following signals: PCIe, Two SATA II, Two USB 2.0, One DisplayPort, One COM port RS-232, HDA, LPC

Hot Swap

Support for all signals to allow peripheral boards to be hot swapped. The individual clocks for each slot and access the backplane ENUM# signal comply with the PICMG 2.1 Hot Swap Specification

I/O Extension Connector

18-pin I/O extension connector holding 1 x SATA port for the SATA NAND Flash module** The SATA NAND Flash module is only available in 4HP

LED´s

6 x LED’s: 4 x POST Code or General Purpose, WD, TH

MTBF

CP3002: 250,129 h acc. to MIL-HDBK-217 FN2, Ground Benign, controlled at 30°, CP3002-HDD: 1,901,991 h acc. to MIL-HDBK-217 FN2, Ground Benign, controlled at 30°

Operating Temp.

0°C to 60ºC, standard (depending on processor version and airflow in the system)

Platform Controller Hub Mobile Intel QM57 Express Chipset

SATA host controller with six ports with RAID 0/1/5/10 support, USB 2.0 host interface with up to 14 ports (6x ports are used on the CP3002), 2 x PCI Express x4 or 8x PCI Express x1 2.0 ports (only 2x PCI-Express x1 are used)

Power Consumption

Core i7-620LE 2.0 GHz and 4GB memory typ. 28W

Processor

Intel Core i7 processor (32nm manufacturing process): Core i7-620LE: 2.0 GHz, LV, 4MB L3 cache (shared instruction/data cache between both cores), Core i7-610E: 2.53 GHz, SV, 4MB L3 cache (shared instruction/data cache between both cores) All board versions are passive cooled with a heatsink within 4HP height. Please contact Kontron for further information concerning the suitability of other Intel processors for use with the CP3002.

Rear I/O via J2

The CP3002 supports two SATA II ports, two Gigabit Ethernet ports without LED signals, two USB 2.0 ports, one VGA analog port, two COM ports (LVTTL signal level), five GPIs and Three GPOs (LVTTL signal level), and power management signals.

RTC

Integrated in QM57 with 256 Byte CMOS RAM

SATA NAND Flash

Up to 16 GB SLC NAND Flash on a dedicated SATA NAND Flash module*The SATA NAND Flash module is only available in 4HP

Serial ATA

1 x onboard standard SATA connector

Software Support

AMI uEFI, setup console redirection to serial port (VT100 mode) with CMOS setup access, EFI Shell support, Board configuration via Shell, diskless, keyboardless, videoless operation, LAN boot support, Board identification number accessible via EEPROM, Support for Windows XP, Windows 7, Windows Embedded Standard 7, Windows Server 2003, Windows Server 2008, Linux, Wind River Linux, VxWorks, QNX (Other OSs may also be used with the CP3002. Please contact Kontron for further information.)

Storage Temp.

-40°C to +85ºC (without additional components)

Supervisory Functions

Watchdog, software configurable, 125ms to 4096s in 16 steps, generates IRQ or hardware reset, dual-stage configuration

System Memory

Up to 8 GB dual channel DDR3 SDRAM running at 1066 MHz, with ECC, via two SODIMM sockets

Trusted Platform Module (TPM)

Infineon SLB9635TT TPM 1.2 controller, optional

UART

XR16L2750IM-F, dual UART, 16C550-compatible

USB

2 x USB 2.0 ports, 4-pin standard USB connectors

VGA

1 x VGA-CRT 15-pin D-Sub connector
High performance 3D graphics controller integrated in the processor:

Watchdog

FPGA-based, timeout ranging from 125ms to 4096s programmable in 16 steps, IRQ, Reset, dual-stage

Weight

CP3002 4HP: 340 g, CP3002 8HP: 480 g