Cooling

ATCA: PICMG 3.0 AdvancedTCA Base Specification R2.0 MicroTCA: PICMG MTCA.0 Micro Telecommunications Comp. Architecture R1.0 AMC: PICMG AMC.0: Advanced Mezzanine Card Specification R2.0 PICMG AMC.1: PCI Express and Advanced Switching R1.0 PICMG AMC.2: Gigabit Ethernet R1.0 PICMG AMC.3: Storage Interfaces R1.0 IPMI: IPMI Intelligent Platform Management Interface Spec. V2.0 IPMI - Platform Management FRU Information Definition V1.0 PCI Express: PCI Express Base Specification Revision 1.0a Serial ATA: Serial ATA 2.5 Specification CE: EN55022, EN55024, EN61000-6-2/-6-3, EN300386, EN60950-1 Vibration/Shock: IEC60068-2-6 / IEC60068-2-27 Climatic Himidity: IEC60068-2-78 WEEE: Directive 2002/96/EC RoHS: Directive 2002/95/EC

Environment

Operating temp.: -5°C to +55°C (depending on system environment) Storage temp.: -40°C to +70°C Humidity: Operational: 5%-90% (non-condensing) Non-Operating: 5%-95% (non-condensing)

External Card

Serial EEPROM (24LC64) 64 kbit

FSB

Two redundant 1 MB Firmware hubs (FWH)

Max. Speed

AMI BIOS, BIOS parameters saved in EEPROM, Boot order defined via MMC Serial over Lan, Support for Linux CGL

Memory

Dimensions: 181.5 mm x 148,8 mm x 18.96 mm (mid-size/double-width) MTBF: tbd acc. Bellcore Issue 6, Ground Benign, Controlled, 30 C

Mini PCI

Microcontroller with 40 kB RAM and redundant 512 kB Firmware Flash with automatic roll-back strategy. The MMC carries out IPMI commands such as monitoring several onboard temperature conditions, board voltages and the power supply status, and managing hot swap operations. The MMC is accessible via a local IPMB (IPMB-L) and two host Keyboard Style Interfaces (KCS).

Miscellaneous

Gigabit Ethernet: 2x 1000BASE-TX on RJ45 connector Serial Port: 1x RS232 UART interface on RJ45 connector USB interface: 2x USB 2.0 port on 4-pin standard USB connector DVI-I: 1x 29-pin VGA DVI I connector for analog or digital monitor LEDs: Four control and status bi color (red/green) LEDs
PCI Express:1 x4 or 4 x1 PCI Express interface AMC fat pipes region port 4-7 Gigabit Ethernet: 2x 1000BASE-BX (SerDes) on AMC ports 0-1 (Common Options Region) Serial ATA: 2x Serial ATA 150 ports on AMC ports 2-3 (Common Options Region) Serial Interface: 1x Serial Port (COM2) on AMC port 15 (Extended Options Region) Debug Interface: 1x Debug Port ona AMC port 14 (Extended Options Region)

Mode

Intel® 3100 chipset with integrated:Three x4 PCI Express ports, DDR2 SDRAM memory controller with ECC, six SATA 150 ports, four USB 2.0 ports, two UARTs, RTC, Interrupt Memory and I/O Controller Hub: Controller, Timer Gigabit Ethernet: Two Intel® 82571EB dual Gigabit Ethernet PCI Express bus controller Graphic: ATI ES1000 graphic controller with PCI 32-bit / 33MHz interface, maximum resolution of 1600x1200 pixels, external 64 MB DDR2 memory Watchdog: FPGA based, software configurable, two-stage Watchdog with programmable timeout ranging from 125 msec to 256 sec in 12 steps. MMC: Microcontroller with on-chip 512 kB Flash and 40 kB RAM, ext. 1 MB SPI Flash, 64 kbit EEPROM RTC: Integrated in 3100 and CMOS RAM with backup, battery replaceable.

On-board EIDE

Up to 8 GByte NAND Flash via onboard USB 2.0 Flash controller

Power Requirement

With Core 2 Duo, 1.5 GHz, 2 GB: max. 37 W

Processor

Intel® Core™2 Duo L7400 (LV), 1.5 GHz, 667 MHz FSB, 4 MB L2 cache 479-pin µFCBGA package, 2x 32KB L1 cache and 4 MB L2 cache The processor is passive cooled with a fanless heatsink. Forced air cooling at a specific flow rate is required.

System Memory

Up to 2 GByte (soldered) registered DDR2 400 MHz with ECC