Cooling

PICMG AMC.0: Advanced Mezzanine Card Specification R2.0 PICMG AMC.1: PCI Express and Advanced Switching R1.0 PICMG AMC.2: Gigabit Ethernet R1.x PICMG AMC.3: Storage Interfaces R1.x IPMI Intelligent Platform Management Interface Specification, V1.5 EMC Directive 89/336/EEC, EN 55022, EN 55024 (Europe) EN 300 386 Designed to meet: FCC 47 CFR Part 15, Subpart B (USA) CISPR22 VCCI (Voluntary Japan Electromagnetic Compatibility requirement) UL 60950, 3rd edition (US and Canada) EN 60950-1 (Europe) LVD 73/23/EEC (Europe) Denan Law (Japan Safety)

Environment

Operating temp.: -5C to +55C (depending on system environment) Storage temp.: -55C to +85C Humidity: Operational: 5%-90% (non-condensing) Non-Operating: 5%-95% (non-condensing)

External Card

Serial EEPROM (24LC64) 64 kbit for CMOS data storing (no battery backup)

FSB

Soldered, up to 2 GByte via onboard IDE Flash controller for application code Two redundant 1 MB Firmware hubs (FWH)

Max. Speed

AMI BIOS, BIOS parameters saved in EEPROM, Boot order defined via MMC Serial over Lan, Support for Linux CGL

Memory

Dimensions: 181.5 mm x 73.5 mm Single-width, full-height, extended full-height MTBF: 216,209 h acc. Bellcore Issue 6, Ground Benign, Controlled, 30C

Mini PCI

Microcontroller with 4 kB RAM: Two redundant 128 kB flash chips (one internal, one external) Communication capabilities: Keyboard Controller Style (KCS) interface to the onboard processor, local Intelligent Platform Management Bus (IPMB-L) to the carrier serial debug interface for test purposes Comprehensive MCC monitor/control support: Processor and chipset supervision such as: Reset Board Flash fail-over mechanism Monitor BIOS POST code Onboard Power Supply Supervision such as: AMC payload power AMC management power Various onboard supply voltages Temperature control for processor, board, chipset, GbE controller

Miscellaneous

PCI Express: One x4 PCI Express interface AMC fat pipes region port 4-7 (root complex) Gigabit Ethernet: Two Gigabit Ethernet 1000BASE-BX (SerDes) ports AMC common options region port 0-1 Serial ATA: Two Serial ATA 150 ports AMC common options region port 2-3
USB interface: One USB 2.0 host port on 5-pin MiniUSB type A/B connector One COM port on 9-pin Dsub connector LEDs: Light pipe: LED 0 (blue): hot swap LED 1 (red) LED 2 (green): general purpose or over temperature LED 3 (amber): general purpose or watchdog Four general purpose LEDs (debug LEDs for POST code) Alternatively used: LED 0/1: Ethernet port 0/1 link signal LED 2: SATA / Flash activity (application code) LED 3: MMC Debug LED

Mode

Memory Controller Hub: Intel E7320 chipset Two x4 PCI Express ports, DDR2 memory controller with RASUM features such as ECC, retry on uncorrectable error, integrated memory scrub engine, memory sparing function I/O Controller Hub: Intel 6300ESB chipset SATA 150, PATA 100, USB 2.0, UART, RTC, Interrupt Controller, Timer Gigabit Ethernet: Intel 82571EB dual Gigabit Ethernet PCI Express bus controller Watchdog: FPGA based Software configurable two-stage Watchdog with programmable timeout ranging from 125 msec to 256 sec in 12 steps. MMC: Microcontroller with dual 128 kB Flash and 4 kB RAM

Power Mode

1.4 GHz, 1 GB mem: typ. 24 W, max. 28 W 1.8 GHz, 2 GB mem: typ. 34 W, max. 40 W

Processor

Intel Celeron M and Pentium M Processor (90 nm), 479-pin FCBGA package, 2x 32 KB L1 cache and 1/2 MB L2 cache, 400 or 533 MHz processor system bus. For Mid-size AM4002: Pentium M 738 LV, 1.4 GHz (low voltage), 2 MB L2 cache, FSB 400 MHz Pentium M 745, 1.8 GHz, 2 MB L2 cache, FSB 400 MHz For Full-size AM4002 with extended heat sink: Pentium M 760, 2.0 GHz, 2 MB L2 cache, FSB 533 MHz The processor is passive cooled with a fanless heatsink. Forced air cooling at a specific flow rate is required.

System Memory

Up to 2 GByte registered DDR2 400 MHz memory with ECC on dedicated memory module (4 GByte when 1 Gbit memory chips available)