1 INTRODUCTION ORDER CODE / INFORMATION 1.4 ORDER CODE / INFORMATION 1 269/269Plus ****** 269/269Plus Motor management relay SV Standard version D/O Drawout version 1 Phase CT Ground CT (required for D/O only) 1 :5 2000:1 2 :5 :5 3 :1 2000:1 4 :1 :5 2 Relay Failsafe Code (required for D/O only) Trip Alarm Aux1 Aux 2 1 FS NFS NFS FS 2 NFS FS NFS FS 3 FS FS NFS FS 4 NFS NFS FS FS 5 FS NFS FS FS 6 NFS FS FS FS 7 FS FS FS FS 8 NFS NFS NFS FS 3 Relay contact arrangement (required for D/O only) Alarm Aux1 Aux2 1 N.O. N.O. N.O. 2 N.O. N.O. N.C. 3 N.O. N.C. N.O. 4 N.O. N.C. N.C. 5 N.C. N.O. N.O. 6 N.C. N.O. N.C. 7 N.C. N.C. N.O. 8 N.C. N.C. N.C. 100P 100 Ohm Platinum RTD 10C 10 Ohm Copper RTD 100N 100 Ohm Nickel RTD 120N 120 Ohm Nickel RTD HI 90 to 300 V DC / 80 to 265 V AC control voltage 20 to 60 V DC / 20 to 48 V AC control voltage LO 1. For CT ratings greater than 1500:5, consult the factory . . 2. FS = Fail safe: A fail safe relay is one that changes state when control power is applied to the 269/269Plus. NFS = Non fail safe: A non fail safe relay is one that remains on its shelf state when control power is applied to the 269/269Plus. 3. N.O. and N.C. are defined as open and closed contacts of an output relay with control power applied to the 269/269Plus and no trips or alarms present. EXAMPLE: For a 269Plus with options: 269PLUS-SV-100P-HI For a 269 Drawout with options: 269-D/O-3-4-7-100P-HI The 269 Plus relay is almost entirely field programmable. The information shown above must be specified when the relay is ordered, as these options are not selectable in the field. Additional features can be made available on special order by contacting GE Multilin. * CT information, failsafe code, and contact arrangement must be specified for drawout relays only; on standard 269 Plus models these features are field selectable. ** See Glossary for definitions GE Multilin 269 Plus Motor Management Relay 1-5 TECHNICAL SPECIFICATIONS 1 INTRODUCTION 1.5 TECHNICAL SPECIFICATIONS 1 PHASE CURRENT INPUTS TRIP/ALARM DELAY TIME ACCURACY conversion: calibrated RMS, sample time 2 ms short circuit trip: instantaneous: 15 to 45 ms delayed: ±1.5 seconds range: 0.05 to 12 × phase CT primary amps setpoint ground fault: instantaneous: 15 to 45 ms delayed 0.5 sec.: ±150 ms full scale: 12 × phase CT primary amps set- delayed over 1 sec.: ±1 s or ±2.5% point of total trip time accuracy: ±0.5% of full scale acceleration trip: ±200 ms or ±2% of total trip time (0.05 to 2 × phase CT primary amps setpoint) single phasing: ±1.5 seconds ±1.0% of full scale immediate overload: 0.3 to 0.7 seconds (over 2 × phase CT primary amps mechanical jam: ±1.5 seconds setpoint) rapid trip: ±1.0 seconds Frequency: 25 to 400 Hz sine wave undercurrent: ±1.5 sec. or ±2% of total trip time GROUND FAULT CURRENT INPUT current unbalance: ±1.0 sec. or ±2% of total trip time conversion: calibrated RMS, sample time 2 ms metering: ±6.0 sec. ±2% of total trip time range: 0.1 to 1.0 × G/F CT primary amps RTD INPUTS setpoint (5 A secondary CT) sensor types: 10 Ω copper 0.3 to 10.0 amps 50:0.025 A 100 Ω nickel (2000:1 ratio) 120 Ω nickel full scale: 1 × G/F CT primary amps setpoint 100 Ω platinum (5 A secondary CT) (specified with order) 10 A (2000:1 CT) display accuracy: ± 2°C accuracy: ±4% of G/F CT primary amps set- trip/alarm setpoint point (5 A secondary CT) range: 0 to 200°C ±0.3 A primary (2000:1 CT HGF 3”) dead band: 3°C Frequency: 20 to 400 Hz for 5 A CTs maximum lead 20 to 150 Hz for 2000:1 CTs resistance: 25% of RTD 0°C resistance OVERLOAD CURVES ANALOG CURRENT OUTPUT (4-20 mA STANDARD) curves: 8 curves fixed shape 1 custom curve PROGRAMMABLE trip time accuracy: ±1 sec. up to 13 sec. OUTPUT 0-1 mA 0-20 mA 4-20 mA ±8% of trip time over 13 sec. detection level: ±1% of primary CT amps MAX LOAD 2000 Ω 300 Ω 300 Ω UNBALANCE MAX OUTPUT 1.01 mA 20.2 mA 20.2 mA display accuracy: ±2 percentage points of true nega- tive sequence unbalance (I /I ) n p accuracy: ±1% of full scale reading RUNNING HOURS COUNTER polarity: terminal 58 (“–”) must be at ground accuracy: ±1% potential (i.e. output is not isolated) DIFFERENTIAL RELAY INPUT Isolation: non-isolated, active source relay response time: 100 msec. maximum Update Time: 250 ms max. (contact closure to output relay acti- COMMUNICATIONS vation) Type: RS485 2-wire, half duplex, isolated RELAY LOCK-OUT TIME Baud Rate: 300, 1200, 2400 accuracy: ±1 minute with control power ® Protocol: Subset of Modbus RTU applied Functions: Read/write setpoints (03/16), ±20% of total lock-out time with no Read actual values (03/04) control power applied 1-6 269 Plus Motor Management Relay GE Multilin 1 INTRODUCTION TECHNICAL SPECIFICATIONS RELAY CONTACTS CONTROL POWER (INCLUDES TOLERANCES) Frequency: 50/60 Hz VOLTAGE MAKE/CARRY MAKE/ BREAK 1 LO range: 20 to 60 V DC CONTINUOUS CARRY 0.2s 20 to 48 V AC RESISTIVE 30 VDC 10 30 10 HI range: 90 to 300 V DC 125 VDC 10 30 0.5 80 to 265 V AC 250 VDC 10 30 0.3 Max. power consumption: 20 VA INDUCTIVE 30 VDC Voltage low ride-through time: 100 ms 10 30 5 (L/R=7ms) (at 120 V AC/125 V DC) 125 VDC 10 30 0.25 Relay can be powered from either AC or DC 250 VDC 10 30 0.15 source. If Control Power input exceeds 250 V, an RESISTIVE 120 VAC 10 30 10 external 3 A fuse must be used rated to the NOTE required voltage. 250 VAC 10 30 10 INDUCTIVE 120 VAC INTERNAL FUSE SPECIFICATIONS 10 30 4 PF=0.4 T3.15A H 250 V 250 VAC 10 30 3 Timelag high breaking capacity configuration FORM C NO/NC DIELECTRIC STRENGTH ROUTINE TEST contact material silver alloy 2200 V AC, 50/60 Hz for 1 sec. minimum permissible GROUND (Terminal 42) to load: 5 V DC, 100 mA Output Contacts (Terminals 29 through 40) 12 V AC, 100 mA Control Power (Terminals 41 & 43) Current Transformer Inputs (Terminals 72 SWITCH INPUTS through 83) Type: Dry contacts If Hi-Pot tests are performed, jumper J201 DO NOT CONNECT LIVE CIRCUITS TO THE DIGI- TAL SWITCH INPUTS. THEY ARE DESIGNED FOR beside Terminal 43 should be placed in the “HI- CAUTION DRY CONTACTS ONLY! POT” position. Upon completion of Hi-Pot NOTE tests, the jumper should be placed in the CT BURDEN DUE TO CONNECTION OF RELAY “GND” position. See Figure 5–3: HI-POT TEST- ING on page 5–7. CT INPUT BURDEN (AMPS) To avoid electrical shock, discharge J201 by (VA) (mΩ) shorting across the pins before reconnecting PHASE 10.04 43 WARNING the J201 jumper. CT 40.5 31 (1A) 13 4.8 28 PHASE 50.06 2.4 CT 20 1 2.5 (5A) 65 8.5 2.01 G/F CT 50.08 3 (5A) 10 0.3 3 G/F CT 0.025 0.435 696 Ω (50:0.025) 0.1 3.29 329 Ω 0.5 50 200 Ω CT THERMAL WITHSTAND Phase CT (1A, 5A) & G/F 5A tap: 3 ×: continuous 6 ×: 40 sec. 12 ×: 3 sec. Phase CT 1A & 5A: 40 x: 2 sec. 80 x: 1 sec. G/F 50:0.025 mA: 6 ×: continuous GE Multilin 269 Plus Motor Management Relay 1-7 TECHNICAL SPECIFICATIONS 1 INTRODUCTION TYPE TESTS PACKAGING Dielectric Strength: 2.0 kV for 1 minute to relays, CTs, Shipping box: 11.40" x 7.50" x 16.00" (W × H × D) power supply 1 290 mm x 190 mm x 410 mm Insulation Resistance: IEC255-5,500 V DC (W × H × D) Transients: ANSI C37.90.1 Oscillatory 2.5kV/ Ship weight: 3.5 kg 1MHz 7.75 lb. ANSI C37.90.1 Fast Rise 5kV/10ns 269 Plus drawout: Ontario Hydro A-28M-82 Shipping box: 13.25" x 12.50" x 20.50" (L × H × D) IEC255-4 Impulse/High 340 mm x 320 mm x 520 mm Frequency Disturbance Ship weight: 12 kg 26.4 lb. Class III Level Impulse Test: IEC 255-5 0.5 Joule 5kV CERTIFICATIONS RFI: 50 MHz/15W Transmitter ISO: Manufactured to an ISO9001 certi- fied program EMI: C37.90.2 Electromagnetic Interfer- UL: UL recognized (file E83849) ence @ 150 MHz and 450 MHz, 10V/m UL 508 Industrial Control Equipment. Static: IEC 801-2 Static Discharge UL1053 - Ground Fault Protection Humidity: 95% non- condensing Equipment. Temperature: -25°C to +60°C ambient CSA: Certified per C22.2 No.14 - Environment: IEC 68-2-38 Temperature/Humidity Industrial Control Equipment Cycle CE: Conforms to IEC 947-1, IEC 1010-1 Dust/Moisture: NEMA 12/IP53 with proper installa- Overvoltage Category:II tion Pollution Degree: 2 Altitude Rating: 2000m IEC 1010-1 IP Code: 40X OPERATING AMBIENT TEMPERATURE The 269 Plus Drawout does not meet CE compliance. & STORAGE TEMPERATURE –25°C to +60°C HAZARD may result if the product is not used for intended purposes. WARNING This equipment can only be serviced by trained personnel. WARNING Relay contacts must be considered unsafe to touch when the system is energized! WARNING 1-8 269 Plus Motor Management Relay GE Multilin 1 INTRODUCTION MPM OPTION SPECIFICATIONS 1.6 MPM OPTION SPECIFICATIONS 1 PHASE CURRENT INPUTS TYPE TESTS Conversion: true rms, 64 samples/cycle Dielectric strength: 2.0 kV for 1 minute to relays, CTs, VTs, power supply CT input: 1A and 5A secondary Insulation resistance: IEC255-5, 500 V DC Burden: 0.2 VA Transients: ANSI C37.90.1 Oscillatory 2.5 kV/ Overload: 20 x CT for 1 s, 1MHz 100 x CT for 0.2 s ANSI C37.90.1 Fast Rise 5 kV/10 ns Range: 1 to 150% of CT primary nd Ontario Hydro A-28M-82 Frequency: up to 32 harmonic IEC255-4 Impulse/High Accuracy: ±1% of display Frequency Disturbance VOLTAGE INPUTS Class III Level Conversion: true rms, 64 samples/cycle Impulse test: IEC 255-5 0.5 Joule 5 kV VT pri/Sec: direct or 120 to 72000:69 to 240 RFI: 50 MHz/15 W Transmitter Input range: 20 to 600 V AC EMI: C37.90.2 Electromagnetic Interfer- Full scale: 150/600 V AC autoscaled ence @ 150 MHz and 450 MHz, nd Frequency: up to 32 harmonic 10V/m Accuracy: ±1% of display Static: IEC 801-2 Static Discharge ANALOG OUTPUTS Humidity: 95% non-condensing Temperature: –10°C to +60°C ambient OUTPUT Environment: IEC 68-2-38 Temperature/Humidity Cycle 0-1 mA 4-20 mA (T1 option) (T20 option) Dust/moisture: NEMA 12/IP53 MAX LOAD 2400 Ω 600 Ω PACKAGING Shipping box: 8½" × 6" × 6" (L × H × D) MAX OUTPUT 1.1 mA 21 mA 215 cm × 152 cm × 152 cm (L×H×D) Accuracy: ±2% of full scale reading Ship weight: 5 lbs/2.3 kg Isolation: 50 V isolated, activesource CERTIFICATION MEASURED VALUES ISO: Manufactured to an ISO9001 certi- fied program PARAME- ACCURACY RESOLU- RANGE UL: UL listed (file E83849) TER % DISPLAY TION UL 508 - Industrial Control Voltage ±1% 1 V 20 to 100% of Equipment. VT UL1053 - Ground Fault Protection Current ±1% 1 A 1 to 150% of CT Equipment. CSA: Certified per C22.2 No.14 - kW ±2% 1 kW 0 to 65535 kW Industrial Control Equipment kvar ±2% 1 kvar 0 to 65535 kvar It is recommended that all relays be pow- PF ±2% 0.01 ±0.00 to 1.00 ered up at least once per year to avoid Frequency ±0.2% 0.1 Hz 20.00 to 70.00 NOTE deterioration of electrolytic capacitors in Hz the power supply. CONTROL POWER Input: 90 to 300 V DC or 70 to 265 V AC, 50/60 Hz Power: nominal 10 VA maximum 20 VA Holdup: 100 ms typical (@ 120 V AC/125 V DC) GE Multilin 269 Plus Motor Management Relay 1-9