120 WATT FLEX ATX TYPE WITH ACTIVE PFC FXA120-W-F SERIES GENERAL SPECIFICATION This specification describes the performance characteristics of a grounded, with active PFC function, single phase, 120 watts, 5 output level power supply with ATX form factor. In addition, it defines a worldwide safety requirement and electromagnetic compatibility requirement for FLEX ATX Power Supply 1) INPUT Description Min. Typical Max. Condition 90VAC 115/230V 264VAC Full Range; 50/60Hz Input Voltage 2 Amps maximum (excluding output current) at 115 VAC input voltage Input Current(RMS) 1 Amps maximum (excluding output current) at 230 VAC input voltage 47Hz 50/60Hz 63Hz - Line Frequency 30 Amps peak max. for one half cycle of AC 115V (cold start) INRUSH CURRENT 60 Amps peak max. for one half cycle of AC 230V (cold start) The power supply efficiency should not be less than 65% at the Efficiency Maximum load of paragraph 3.1 with the AC input at any nominal low range of high range voltage specific in paragraph 2.1 Power Factor Correction >0.95 at Full Load 2) OUTPUT 2.1) STATIC DC LOAD NOMINAL LOAD CURRENT REGULATION VOLTAGE (DC) MIN. MAX. (%) +3.3 Volt 0.5 A 7 A +/- 5 +5 Volt 1 A 12 A +/- 5 +12 Volt 0.5 A 5 A +/- 5 -12 Volt 0 A 0.3 A +/- 10 +5 Vsb 0 A 1.5 A +/- 5 NOTE: Regulation shows the percentage of absolute value of nominal output voltage. The total output should be 120W max. +3.3V & +5V combined output should not exceed 70W. ETA-USA Tel: 408-778-2793 Fax: 408-779-2753 e-mail: sales@eta-usa.com 2.2) REMOTE ON/OFF CONTROL As logic level is LOW: Output voltage is enabled As logic level is HIGH or floating: Output voltage is disabled. Note: Logic high level: 3.5-5.25 V, Logic low level: 0-0.5 V 2.3) RIPPLE AND NOISE The ripple and noise of the outputs should be measured at the full load Output Voltage Ripple & Noise(p-p) +3.3 Volts 50 mV +5 Volts 60 mV +12 Volts 120 mV -12 Volts 120 mV +5sb Volts 100 MV NOTE; 20MHz bandwidth ripple & noise is measured by using 0.1uF C.C& 10uF/50V E.C bypassed at the output connector. 2.4) HOLD UP TIME The power supply unit should maintain its proper output voltage within voltage specifications for at least 20 milliseconds after losing input power under the condition of 95 VAC input with full loading. 3) OVERSHOOT AT TURN-ON/TURN-OFF Any overshoots during turn-on/turn-off should be less than +/-5% of the nominal output voltage values. No voltage of opposite polarity shall be present on any output during turn-on or turn-off. 4) TEMPERATURE COEFFICIENT The temperature coefficient of all outputs is +/-0.05% per degree C maximum. 5)PROTECTION: 5.1) OVER VOLTAGE PROTECTION(OVP) If any over voltage fault occur, the power supply should latch off before any output exceeds its limit below. NOMINAL OVERVOLTAGE RANGE(V) VOLTAGE(V) FROM TO +3.3 3.7 4.1 +5 5.6 6.5 +12 13.3 14.3 The power supply will not be automatically recovered after the over voltage fault being removed. A manual power reset is necessary. ETA-USA Tel: 408-778-2793 Fax: 408-779-2753 e-mail: sales@eta-usa.com 5.2) SHORT CIRCUIT PROTECTION Any short circuit occurred on any DC output should not cause any damage to the power supply, but will shut down the power supply. The power supply will not be automatically recovered after the short circuit being removed. A manual power reset is necessary. 5.3) OVERLOAD PROTECTION An over load protection will be affected when either of the loadings: +5V, +3.3V & +12V exceeds +110% to 160%. The power supply won’t be automatically recovered after the overload being removed. It needs to do the input power reset. 6) RISE TIME: After turning on, less than 20 mS will be needed for the rise of +5V output voltage(measured from 10% point to 95% point on the waveform) to reach its peak. 7) POWER GOOD SIGNAL: After power-on with nominal AC input, there might be a turn-on delay (between100 mS to 500mS) before the Power Good Signal is issued, which occurs before+5V output reaches its minimum sense level of +4.75V. When turn-off, the Power Good Signal shall go to a lower level for at least 1 mS before +5V falls under the regulation limit described in paragraph 3.1 ETA-USA Tel: 408-778-2793 Fax: 408-779-2753 e-mail: sales@eta-usa.com 8) SAFETY PROVIDED: UL60950-1 CSA22.2 60950-1 TUV EN60950 CB IEC60950-1 FCC Class “B” CE EN55022 class “B” EN61000-3-2 class “D” CE CISPR22 Class B 8.1) DIELECTRIC WITHSTAND --- Primary to Secondary : 3000 VAC for 60 Sec --- Primary to Frame Ground : 1500 VAC for 60 Sec. 8.2) INSULATION RESISTANCE --- Primary to Secondary : 20 Meg. Ohms Min. 500 VDC. --- Primary to Frame Ground : 20 Meg. Ohms Min. 500 VDC. --- Secondary to Frame Ground : 10 Meg. Ohms Min. 500 VDC. 9) ENVIRONMENT 9.1) OPERATING Temperature 0 to 40 degree centigrade Relative Humidity 10 to 90 percent, non-condensing 9.2) SHIPPING AND STORAGE Temperature -40 to +70 degree centigrade 5 to 95 percent, non-condensing Relative Humidity 10) WARRANTY: One Year (MTBF 80,000 Hrs, DC fan not guaranteed) 11) DIMENSION Case dimension: 150(L) X 83(W) X 41.5(H)mm 12) PIN ASSIGNMENT Flex ATX Main Power Supply Connector PIN 11 PIN 20 ○□□○○□□○○□ □○○□□○○□□○ PIN 1 PIN 10 ETA-USA Tel: 408-778-2793 Fax: 408-779-2753 e-mail: sales@eta-usa.com Pin Signal Wire 1 +3.3 VDC Orange 20AWG 2 +3.3 VDC Orange 20AWG 3 COM Black 20AWG 4 +5 VDC Red 20AWG 5 COM Black 20AWG 6 +5 VDC Red 20AWG 7 COM Black 20AWG 8 POK Gray 22AWG 9 +5 VSB Purple 22AWG 10 +12 VDC Yellow 20AWG Pin Signal Wire 11 +3.3V VDC Orange 20AWG 12 -12 VDC Blue 22AWG 13 COM Black 20AWG 14 PS-ON Green 22AWG 15 COM Black 20AWG 16 COM Black 20AWG 17 COM Black 20AWG 18 NC - - 19 +5 VDC Red 20AWG 20 +5 VDC Red 20AWG ETA-USA Tel: 408-778-2793 Fax: 408-779-2753 e-mail: sales@eta-usa.com