200 – 300 WATTS General Product Specifications: 1U( )Q Model Series 200W – 300W, Multiple Output. Hold-up Time...................Output remains in regulation >20msec mini- -AC Input- mum following loss of AC power at low line, Voltage/Current..............AC 90-264V, 47-63Hz, 5.5A Max, 1 Phase. full load. Over Current/Short Fusing.............................AC 6.3A, 250V internal line fuse provided, Circuit Protection ............Load current hiccup (cycles on/off). Auto- non-user serviceable. matic recovery when overload is removed. Power Factor .................>0.99 line PFC typical at AC 115V, full load. Over Voltage Protection.Non- crowbar type. Output exceeding 25%±10% of nominal Vout will cause the Inrush Current ................Thermistor soft start (~25ºC cold start). out-put to latch off. Remote enable or AC 15Apk @ AC 115V, input recycle required to reset. 30Apk @ AC 230V. -Signals, Indicators and Controls- Transient Protection .......MOV. Withstands transients as specified by EN61000-4-5 (differential / common mode). Remote Enable................Enabled by closed circuit or TTL logic 0. Disabled by open circuit or TTL logic 1. EMI Filtering.....................Meets CISPR22B Level B, and EN 55022 Level B. Power Fail Warning........Loss of input AC causes a TTL compatible signal to go low >4msec prior to the output Efficiency .......................70% typical at AC 115V, full load. dropping out of regulation. At AC turn-on, Redundant/Hot Swap.....Full power N+1 redundant, hot swap signal stays low until the output is in regula- capable. tion. PF signal also triggered by an under voltage condition (V-out 10% below V-nom.) -DC Outputs- LED Indicator ..................Front panel mounted, single-color LED. Voltage/Current (V/A)....Refer to Model Chart. Green indicates AC power ON and output within regulation. Off indicates an input Line/Load Regulation......<±1% at the sense point over full AC input and/or output power fault. range and 0 – 100% output loading, sense leads connected. -Operating Environment- Minimum Loading ............None required for single unit applications. Operating Temperature ..Oº – 50ºC ambient at full load, with speci- 10% loading required in N+1, N2 configura- fied airflow. Derates linearly to 50% at 70ºC. tions. Cooling............................Provided with internal single or dual DC ball Output Turn-on Delay .....<2 sec from AC turn on. bearing fans dependant on output power, <100 msec from remote enable. rated 9 cfm minimum each. Forward airflow intake is at end opposite of I/O terminations. Over/Under Shoot ..........None at turn-on or turn-off. Relative Humidity ............Up to 90% RH, non-condensing. Stability ...........................Output drift <±0.2% after 20 min. warm-up. Operating Vibration ........0.75G peak, 5 – 500Hz along three Temp. Coefficient ...........<±0.02%/ºC, 0-50ºC, after 20 min. warm-up. orthogonal axis. Dynamic Response........Less than 3% deviation with a 25% load Storage Temperature .....-40º to 85ºC. change at 1A/msec. Output recovers to within 1% in less than 300msec. Altitude ...........................Operating to 10,000 ft. Storage to 30,000 ft. Ripple & Noise MTBF..............................Designed for 150,000 hours at 25ºC. (PARD) ...........................50mV max or <1% peak-to-peak nominal, whichever is greater, at the output terminals -Interconnect- with a 20 Mhz bandwidth limit. May be Multiple Output Model...38-circuit, sequential contact, hot pluggable measured with 0.1mF ceramic capacitor in type. parallel with a 22mF tantalum. Positronic Ind. P/N PCIH38M400A1-241.1. Current Sharing/ Mates with PI P/N PCIH38F300A1 Parallel N+1 Operation....Single wire connection for ±10% current Note: Use of the specified mating connector is required to insure sharing between any number of units. proper "make/break" sequential contact sequence. Remote Sense................Output compensates for up to 0.5V total line drop in the load cables. Output internally sensed if leads are opened. Over Temperature Protection .......................Internal temperature sensing. Automatic recovery. Multiple Output Models Input: Model: V1 (Main) V2 V3 V4 Fans: ~100-240V Output: 50/60Hz Single Phase Volts @ Amps 200 Watt: Input Amps: 1UEQ201HP 3.0A Max 5V, 25.0A 3.3V, 25.0A 1UEQ202HP 5V, 25.0A 12V, 10.0A 1UEQ203HP 5V, 25.0A 15V, 6.0A 1UEQ204HP 3.3V, 25.0A 12V, 10.0A 1UEQ301HP 5V, 25.0A 12V, 8.0A 12V, 3.0A 1UEQ302HP 5V, 25.0A 3.3V, 20.0A 12V, 3.0A 1UEQ303HP 5V, 25.0A 12V, 8.0A 5V, 4.0A 1UEQ304HP 5V, 25.0A 15V, 6.0A 15V, 3.0A 1UEQ305HP 5V, 30.0A 15V, 2.0A 15V, 2.0A 1UEQ401HP 5V, 25.0A 12V, 8.0A 12V, 3.0A 12V, 3.0A 1UEQ402HP 5V, 25.0A 12V, 8.0A 12V, 3.0A 5V, 3.0A 1UEQ403HP 5V, 25.0A 3.3V, 15.0A 12V, 3.0A 12V, 3.0A 1UEQ404HP 5V, 25.0A 3.3V, 15.0A 12V, 3.0A 5V, 3.0A 300 Watt: 1UFQ201HP 4.5A Max 5V, 40.0A 3.3V, 40.0A 1UFQ202HP 5V, 40.0A 12V, 15.0A 1UFQ203HP 5V, 40.0A 15V, 15.0A 1UFQ204HP 3.3V, 40.0A 12V, 15.0A 1UFQ301HP 5V, 30.0A 12V, 10.0A 12V, 3.0A 1UFQ302HP 5V, 30.0A 3.3V, 30.0A 12V, 3.0A 1UFQ303HP 5V, 30.0A 12V, 10.0A 5V, 3.0A 1UFQ304HP 5V, 30.0A 15V, 8.0A 15V, 3.0A 1UFQ305HP 3.3V, 30.0A 12V, 10.0A 12V, 3.0A 1UFQ401HP 5V, 30.0A 12V, 9.0A 12V, 3.0A -12V, 1.0A 1UFQ402HP 5V, 30.0A 12V, 9.0A 12V, 3.0A -5V, 1.0A 1UFQ403HP 5V, 30.0A 3.3V, 30.0A 12V, 3.0A -12V, 1.0A 1UFQ404HP 5V, 30.0A 3.3V, 30.0A 12V, 3.0A -5V, 1.0A Remote Sense......................... P1-24, P1-26, P1-27. V1, V2 outputs 1U()Q Multiple Output Input/Output and compensate for up to 0.5V total line Signal Connector Type and Pin Functions: drop in the load cables. Current Sharing/ Positronics Ind. P/N PCIH38M400A1.315. 38-circuit hot plug- Parallel N+1 Operation.......... P1-32, P1-33. Single wire connection able type. Glass filled polyester insulator material, rated 94V-0. for V1 and V2. ±10% current sharing Secured in the unit rear. Use of Positronic PCIH38F300A1 between any number of units. series mating connector is required to ensure correct mating contact sequence and current capacity. Remote DC Enable................ P1-25. Enabled by closed circuit or TTL logic 0. Disabled by open PIN# SEQ FUNCTION circuit or TTL logic 1. 01-02 2 N/U Not Used. 03-04 2 +5.0V V1 Output. Remote DC Inhibit ................ P1-31. Enabled by open circuit or 05-06 2 GND V1 Return. TTL logic 1. Disabled by closed 07-10 2 N/U Not Used. circuit or TTL logic 0. 11-12 2 GND V2 Return. 13-14 2 +3.3V V2 Output. Other Features: 15-16 2 N/U Not Used. 17 2 +12.0V V3 Output. Undervoltage Protection........ Auto DC output shutdown when AC 18 2 GND V3 Return. input falls below safe operating 19,20 2 N/U Not Used. 21 2 -12.0V V4 Output. limits (» 80VAC). Automatic 22,23 2 GND V4 Return. recovery. 24 2 +S1 +5.0V (V1) Remote Sense. Minimum Loading................. None required. 25 3 R/EN Remote Enable. Close circuit to GND. 26 2 S-RTN Sense Return for V1, V2. Over Current/Short 27 2 +S2 +3.3V (V2) Remote Sense. Circuit Protection .................. Standard hiccup mode (on/off cycle) 28-30 2 N/U Not Used. current limit when Vout current is 31 2 R/INH Remote Inhibit. Close circuit to GND. 32 3 ISHR-1 +5.0V (V1) Current Share. >105% to 120% of full load. Auto- 33 3 ISHR-2 +3.3V (V2) Current Share. matic recovery when overload is 34 3 N/U Not Used. removed. 35 2 PF Power Fail Signal. Over Voltage Protection ........ Non-crowbar type. Any output that 36 1 PE Primary Earth (chassis) Safety Ground. 37 2 ACC Neutral AC Power Input. exceeds 25% ±10% of nominal Vout 38 2 AC Line AC Power Input. will cause Vout to latch off. Remote enable or AC input recycle required Indicators and Controls: to reset. Over Temperature LED 1: DC Power Good. Located on the front panel. The Protection .............................. Internal temperature sensing. Causes power supply is functioning within specifications when Vout to shut down. Automatic the LED indicator is green. Off indicates an input or recovery. output fault condition. Power Fail Warning............P1-35. Loss of input AC causes a TTL compatible signal to go low >4mSec prior to the output dropping out of regulation. At AC turn-on, signal stays low until output is in regulation. PF signal also triggered by an under voltage condition (V-out drops 10% below V-nom.) Mechanical Specifications Multiple Output. PCB BACK PLANE .86 .237 ( 21 .8 ) 2 1 ( 6 ) A .64 BACK PLANE CONNECTOR (16.4 ) 20 19 5.00 2 1 23 2 2 (127 ) 33 35 34 3 6 3 7 3 8 A .200 11.50 ( 5.1 ) (292.1 ) AIR FLOW DIRECTION 1.60 (40.6 ) .20 .50 (5.1) (12.7) MIN MAX .40 4.20 ( 10.2 ) ( 106.7 ) .25 O (6.4 ) GUIDE PIN 2 PLACES .25 (6.3 ) .96 (24.4 ) 2 PLACES ALIGNMENT OPTION 1 (FOR HORIZONTAL AND VERTICAL MOUNT CONFIGURATIONS) SOUTHCO P/N .14 (27-10- 311- 30) ( 3.6 ) TYP. .14 .47 ( 3.6 ) (12 ) .15 (3.8 ) 2 PLACES .240 .260 (1) (6.1 ) (2) VIEW A-A VIEW A-A ( 6.6 ) 2.38 ROTATED 90 CW VERTICAL MOUNT CONFIGURATION 2 PLACES ( 60.4 ) HORIZONTAL MOUNT CONFIGURATION .55 (14 ) .63 .1 2 (16 ) .18 ( 2.9 ) .93 (4.6 ) ( 23.6 ) .62 .120 R GUIDE CUT-OUT .18 (15.8 ) ( 3 ) (4.6 ) (GUIDE PIN IN RACK NOT .240 TO EXCEED .125 (3.2) HIGH ( 6.1 ) .52 (13.2 ) ALIGNMENT OPTION 2 (FOR HORIZONTAL MOUNT CONFIGURATION ONLY) ETA-USA 16315 Vineyard Blvd. Morgan Hill, CA 95037 Ph: 408-778-2793 Fax: 408-779-2753 e-mail: sales@eta-usa.com Web: www.eta-usa.com