CPX8216 Series CompactPCI High Availability System Front page The Emerson Network Power CPX8216 system is a dual 8-slot, 12U, carrier-grade The Emerson CPX8216 ® platform with a CompactPCI backplane (with or without a H.110 bus), designed system is a dual 8-slot, 12U, especially for high availability telecommunication infrastructure applications requiring carrier-grade platform with NEBS and ETSI certification. a CompactPCI backplane. With its 5NINES high availability design, the CPX8216 system can be counted on Interior page n Dual 8-slot backplane when you need reliability and availability accompanied by Emerson’s superior level (CPX8216 models) or back- of product support. The CPX8216 is used to support a variety of telecommunication plane with H.110 bus to all applications such as media gateways, packet data gateways, media routers, as well I/O slots (CPX8216T models) as voice messaging, and VOIP applications. It is the flagship product of the Emerson for high availability designs CPX product line, and has been sold since 1999, with thousands of systems in use ® n A PowerPC system controller around the world. CPU allows simplex or duplex configurations n Three 400W hot-swappable AC or DC power supply units provide N+1 redundancy n Front access service and installation of CompactPCI boards, drives and power supplies for easy access to active components n Rear connection of I/O allows card removal without disconnecting field wiring n Detection of power, temperature, and fan fail conditions supports remote reporting ® n Adherence to PICMG 2.0 rev. 2.1, PICMG 2.1 rev. 1.0, PICMG 2.5 rev. 1.0 CompactPCI industry standard specifications provide worldwide acceptance and conformance Front page Interior page Specifications CHASSIS ƒ Earth Ground: Two points at rear, per NEBS requirements ƒ Size: 21.00" [533 mm] high (12U), 18.90" [480 mm] wide including mounting flanges, 17.13" [435 mm] ƒ Metal: Aluminum alloy, T5052-H32 deep from mounting flanges ƒ Metal Plating: Chemical film per MIL-C-5541, clear ƒ Weight: Approx. 30 lb. [13.6 kg] unloaded. Approx. ƒ Slot, LED, & Switch Marking: Black silk 70 lb. [31.85 kg] fully loaded. ƒ Mounting: Per EIA Standard RS-310-C in 19" rack HOT SWAP CONTROllER (HSC) BRIdgE CARd or 23" rack with mounting brackets ƒ Form Factor: 80 mm rear transition (CPX8216 ƒ Slots: 16 hot swap-capable single-width (4HP) models) 160 mm front loaded (CPX8216T models) CompactPCI slots (two CPU, two HSC bridge and ƒ Control: CompactPCI bus and slot control per twelve I/O boards, IEEE 1101.10 compatible); 16 CompactPCI Hot Swap Specification 80mm transition slots, IEEE 1101.11 compatible ƒ Alarm Status Registers: Yes ƒ Power Supplies: Three bays, front accessible ƒ Hot Swappable: Yes ƒFR Air Flo ONT VI w: F EW ront inlet, rear exhaust ƒ ESD Grounding: Two ESD ground points, one front and one rear FRONT VIEW Alarm Redundant CPU CD ROM Hot Swap Panel Boards Drive Drive Carriers SYSTEM STATUS TELCO SYSTEM IN COMPONENT OUT SYSTEM OUT MINOR MAJOR CRITICAL ALARM SERVICE OF SERVICE OF SERVICE 79 1 2 3 4 5 6 11 12 13 14 15 16 21.00 in. (12U) 79 1 2 3 4 5 6 11 12 13 14 15 16 ESD Ground HSC Bridge Boards IN OUT OF IN OUT OF IN OUT OF SERVICE SERVICE SERVICE SERVICE SERVICE SERVICE 17.50 in. 19.00 in. Cable Pass-Thru Redundant Fan/ Power Supply Modules 2 Front page Interior page REAR VIEW Floppy SCSI ESD Redundant HSC Redundant CPU REAR VIEW Drives Inputs Ground Bridge Boards Transition Boards 97 16 15 14 13 12 11 11 8 6 5 4 3 2 1 97 16 15 14 13 12 11 11 8 6 5 4 3 2 1 Redundant DC Inputs Dual Earth Ground DC Breaker/Switch AC Switch/Receptacle (DC Input Version) Attachment Points (DC Input Version) (AC Input Version) BACkPlANE HOT SWAP dRIVE CARRIERS A hot swap drive carrier option can be installed in any of ƒ Domains: Two 8-slot, 64-bit CompactPCI; H.110 the front four drive bays (EIDE). bussed to all I/O slots on CPX8216T models ƒ Slots: One CPU slot, one HSC bridge slot, and six I/O REmOVABlE mEdIA dRIVES slots per domain Up to two internal floppy drives (one per domain) ƒ DC Power Distribution: Yes can be installed in the rear of the chassis. ƒ Alarm Signal Routing: Yes USER NOTE: SPECIFICATIONS FOR 2.5" dISk dRIVES HOT-SWAPPABlE AlARm Your attention is directed to the fact that the MTBF ƒ CompactPCI Slot LEDs: Two for each slot; in service of any drives mounted on these blades must be considered and out of service independently of the MTBF of the blades themselves. Also, the supported operating parameters of the drives ƒ Telco Status LEDs: Minor, major and critical may differ substantially from those of the blades. ƒ Output: RJ-45 connector with dry relay contacts It is the User’s responsibility to ensure that the HARd dISk ANd Cd-ROm dRIVES operating parameters of these drive offerings are A total of four drives can be mounted in front accessible well understood and taken into consideration when drive bays. Select from: designing operating use. ƒ EIDE hard drives and/or DVD-ROM drives 3 Alarm Indicator Board CPX8216 Backplane Optional H.110 Bus H.110 H.110 Compact PCI-A Compact PCI-B DC Output DC Output DC Output -48VDC/110VAC/220VAC Front page Interior page The operating parameters of our current drive offerings can ElECTRICAl SPECIFICATIONS be found on the Emerson Technical Publications web page at ƒ Power Factor: 0.98 min. at full load, nominal line www.EmersonNetworkPower.com/EmbeddedComputing. (AC only) ƒ Inrush Current: 20 A peak @ 115 VAC for one line POWER SUPPly ANd FAN mOdUlE cycle 20 A peak @ –36 VDC within 4ms The CPX8216 uses up to three, 400W, hot-swappable ƒ Efficiency: >70% @ full load, nominal line – DC power supplies in an N+1 redundant configuration. version >72% @ full load, nominal line - AC version Each supply is load sharing and diode protected. The ƒ Output Power: 400W in this app lication assembly supports the power supply, blind mate ƒ Hold-Over Storage: 20 ms at full load @ 115 VAC connectors and interconnect wiring harness. Either AC or DC versions are available. ƒ Transient Response: All outputs return to 1% within 2 ms of a 25% load change COOlINg FEATURES ƒ Dynamic Load: The supply operates properly when ƒ Three hot-swappable, N+ 1 modules in system subjected to a 10% load delta with a 50% duty cycle, from 0 to 2 times switching frequency ƒ DC tube axial fan (removable/replaceable) ƒ Over Voltage Protection: +5V output < 6.25 VDC ƒ Cooling sensor detects airflow and temperature changes +3.3V output <4.2 VDC ƒ Air filter option ƒ Short Circuit Protection: Short between outputs ƒ Software monitoring and speed control causes latch off ƒ LED status indicators CPX8216 System Diagram I/O I/O I/O Power Supply Power Fan I/O & Supply Fan Control I/O Board I/O CPU HSC/Bridge CPU HSC/Bridge Power Supply Power Fan I/O & Supply Fan Control I/O Board I/O I/O I/O I/O Power Power Supply Fan & Supply Fan Control Board Drive Drive Drive Drive 4 A i r f Front page Interior page CPX8216 AIR FlOW* Alarm Board HSC and CompactPCI Transition Boards Boards Power Input DC Fan Air Filter * Diagram for illustrative (Optional) Power Supply purposes only. May not be representative of final product. Power Supply 17.13 in. Control Board Fan/Power Supply Control Board mOdUlE dC OUTPUT Voltage Regulation Min. Load Max. Load Peak Load 5 Sec. Max Ripple P/P +5.05V +/–3% 0.0 A 40.0 A – <50 mV +3.35V +/–3% 0.0 A 40.0 A – <50 mV +12.1V +/–5% 0.0 A 8.0 A 10.0 A 120 mV -12.1V +/–5% 0.0 A 4.0 A – 120 mV Total combined output loading not to exceed 400W. POWER dISTRIBUTION mOdUlE dC Input Version ƒ –36 VDC to –72 VDC input AC Input Version ƒ Double-pole circuit breaker with on/off switch and ƒ 88 – 260 VAC input, auto selecting, 47 – 63 Hz reset ƒ Double-pole rocker on/off switch and IEC AC input ƒ Dual (redundant) input terminal blocks, diode receptacle protected ƒ 12 A maximum input current at 115 VAC ƒ 30 A maximum input current at –48 VDC ƒ 6 A maximum input current at 230 VAC ƒ Tip and ring voltage inputs optional 5 l w w o l f o r i A w o l f A i r r i f l A o w w o l f r i A Front page Interior page Reliability and Serviceability REdUNdANCy WARRANTy Detection, isolation, notification, and replacement of The CPX8000 series is offered with a two-year limited a failed FRU prevents degradation of performance or warranty which reduces the cost of ownership, loss of service during a single fault condition. provides investment protection and demonstrates out commitment to quality and reliability of products to out OEM partners. FIEld REPlACEABlE UNITS (FRUs) Field Replaceable Units Hot Swap Redundant MTTR* CompactPCI Boards X X 5 min. HSC/Bridge Board X X 5 min. Hard Disk Module X X 5 min. Power Supply X X 5 min. Power Distribution Module 5 min. Alarm Board X 5 min. *Mean Time to Replace Software Support COmPONENT ANd SySTEm mTBF ƒ Host CPU and Bridge: 250,000 hours REAl-TImE OPERATINg SySTEmS ƒ Power Supply: 1,000,000 hours VxWorks from Wind River Systems ƒ Alarm Indicator Board: 250,000 hours gENERAl-PURPOSE OPERATINg SySTEmS ƒ Backplane: 7,000,000 hours Linux ƒ Fan: 100,000 hours FAUlT mANAgEmENT SOFTWARE Note: Component MTBF goals are based on acceler- Emerson offers a complete line of Advanced High ated life testing and field data. System MTBF is Availability Software, featuring our award winning demonstrated at accelerated life testing. HA Linux product. REgUlATORy COmPlIANCE POWERPC FIRmWARE ƒ Safety: CSA NRTL/C to standard 22.2 #950, VDE On-board PowerPC firmware expands features like EN60950, CE Mark per European Low Voltage power-up tests with extensive diagnostics, and Directive 72/EEC provides an evaluation and debug tool for simple or ƒ EMC: U.S.: FCC Part 15, Subpart B, Class A high-level development support. It also supports Canada: ICES-003, Class A booting of operating systems and/or real-time kernels. Europe: CE Mark per European EMC Directive 89/ 336/EEC with Amendments; Emissions: INTEl ARCHITECTURE CPU BIOS EN55022 Class A; Immunity: EN50082-1 The CPU BIOS is contained in on-board flash EPROM. It features auto-configuration or extended setup with serial/parallel ports, remapping capabilities and power-on-self-test features. 6 Front page Interior page SOlUTION SERVICES Emerson Network Power provides a portfolio of solution services optimized to meet your needs throughout the product lifecycle. Design services help speed time-to-market. Deployment services include global 24x7 technical support. Renewal services enable product longevity and technology refresh. PICMG and CompactPCI are registered trademarks of the PCI Industrial Computer Manufacturers Group. PowerPC is a trademark of IBM Corp. and used under license. Intel and Pentium are registered trademarks Intel Corporation or its subsidiaries in the U.S. and other countries. All other product or service names are the property of their respective owners. This document identifies products, their specifications, and their characteristics, which may be suitable for certain applications. It does not constitute an offer to sell or a commitment of present or future availability, and should not be relied upon to state the terms and conditions, including warranties and disclaimers thereof, on which Emerson Network Power may sell products. A prospective buyer should exercise its own independent judgment to confirm the suitability of the products for particular applications. Emerson Network Power reserves the right to make changes, without notice, to any products or information herein which will, in its sole discretion, improve reliability, function, or design. Emerson Network Power does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent or other intellectual property rights or under others. This disclaimer extends to any prospective buyer, and it includes Emerson Network Power’s licensee, licensee’s transferees, and licensee’s customers and users. Availability of some of the products and services described herein may be restricted in some locations. AC Power Embedded Power Precision Cooling Emerson Network Power. Connectivity Racks & Integrated Cabinets Infrastructure Management & Monitoring The global leader in enabling ™ DC Power Outside Plant Services Business-Critical Continuity . Embedded Computing Power Switching & Controls Surge Protection Emerson Network Power Emerson, Business-Critical Continuity and Emerson Network Power are trademarks of Offices: Tempe, AZ U.S.A. 1 800 759 1107 or +1 602 438 5720 Madison, WI U.S.A. 1 800 356 9602 or +1 608 831 5500 Emerson Electric Co. or one of its affiliated Paris, France +33 1 60 92 31 20 • Munich, Germany +49 89 9608 2333 • Tel Aviv, Israel +972 9 9560361 2730 Hong Kong, China +852 2176 3540 • Shanghai, China +8610 8563 1122 • Tokyo, Japan +81 3 5403 • Seoul, Korea +82 2 3483 1500 companies. ©2009 Emerson Electric Co. CPX8216-D3 02/09 EmersonNetworkPower.com/EmbeddedComputing