EMERSON iMP
Specifications
AC OK
> 5 ms early warning min. before outputs lose regulation. Full cycle ride thru (50 Hz) (n/a on iMP4 > 750 W @ 90 Vac)
Adjustment range
± 10% minimum all outputs (manual) (full module adjustment range using I2C)
DC OK
± 5% of nominal. Configurable through I2C
Efficiency
Up to 85% @ full case load
Electromagnetic susceptibility
Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3
EMI filter
CISPR 22/EN55022 Level “B”**
External sync
TTL clock input signal used to adjust switching frequency. Frequency 500 kHz ± 20%; Duty cycle 40 - 55%
Factory set point accuracy
± 1%
Frequency
47 - 440 Hz
Global Inhibit/Enable
TTL, Logic “1” and Logic “0”; configurable
Harmonic distortion
Meets EN61000-3-2
Holdover storage
20 ms minimum (independent of input Vac) additional 34ms holdover storage with optional HUP module (SEMI F47 compatible). For iMP4 15 ms (low-line), 10 ms (high-line)
Housekeeping standby
5 Vdc @ 1.0 A max. present whenever AC input is applied (Optional 2.0 A available)
Humidity
Operating; non-condensing 10% to 95% RH
I2C Output program accuracy
± 5%
Input fuse (internal)
iMP4: 16 A; iMP8: 20 A; iMP1: 25 A (both lines fused)
Input range
85 - 264 Vac 120 - 350 Vdc (limited to 300 Vdc in medical applications)
Inrush Current
40 A peak max. (soft start)
Isolation
Meets EN60950 and EN60601
LEAKAGE CURRENT
300 µA max. @ 240 Vac; 47 - 63 Hz
Margining
± 4 - 6% nominal analog (single output module only)
Minimum Load
Not required
Module inhibit
Configured and controlled through I2C
Operating Temperature
-40 ° to 70 °C ambient. Derate each output 2.5% per degree from 50 °C to 70 °C. ( -20 °C start up)
Output/Output isolation
>1 Megohm, 500 V
Overall regulation
0.4% or 20 mV max. (1500W modules 1% max.) (36 W modules 4% maximum)
Overcurrent protection
Configurable through I2C (calibration required). Single output module and main output of the dual output module 105 - 120% of rated output current. Aux output of dual output module 105 - 140% of rated output current
Overvoltage Protection
Configurable through I2C
Overvoltage protection Dual output module
2 - 6 V 122 - 134% ; 8 - 28 V 110 - 120%
Overvoltage protection Single output module
2 - 5.5 V 122 - 134% ; 6 - 60 V 110 - 120%
Overvoltage protection Triple output module
110 - 120% of highest voltage rating
Power Factor
0.99 typ. meets EN61000-3-2 (n/a @ 440 Hz)
Radiated EMI
CISPR 22/EN55022 Level “B”**
Recovery time
To within 1% in
Remote sense
Up to 0.5 V total drop (not available on triple output module)
Reverse voltage protection
100% of rated output current
Ripple
RMS: 0.1% or 10mV, whichever is greater. Pk-Pk: 1.0% or 50mV, whichever is greater. Bandwidth limited to 20 MHz
Short-circuit protection
Protected for continuous short-circuit. Recovery is automatic upon removal of short
Single wire parallel
Current share to within 2% of total rated current
Storage Temperature
-40 °C to 85 °C
Switching frequency
250k Hz accepts external sync signal
Thermal protection
(OTP and OTW)Configurable through I2C. All outputs disabled when internal temp exceeds safe operating range. > 5 ms warning (AC OK signal) before shutdown
Turn-on time
AC on 2.0 sec typ., inhibit/enable 150 ms typical. Programmable delay; 50 ms internal turn-on delay (Dual Output only)
Vibration
IEC68-2-6 to the levels of IEC721-3-2
Features
- Configurable current limit (foldback or constant current)
- Configurable inhibit/enable
- Configurable input and output (case and module) OK signals and indicators
- Configurable output UP/DOWN sequencing
- Customer provided air option
- Downloadable GUI from website
- External switching frequency sync input
- High power density (8.8 W/cu-in)
- I2C monitor of voltage, current, and temp
- Increased power density to 50% over standard MP
- Industrial shock/vibration (> 50G’s)
- Industrial temp range (-40 ºC to 70 ºC)
- Intelligent fan (speed control/fault status)
- Intelligent I2C control
- No preload required
- Optional conformal coating
- Optional extended hold-up module (SEMI F47 compliance)
- Programmable voltage, current limit, inhibit/enable through I2C
- uP controlled PFC input with active inrush protection
- Voltage adjustment on all outputs (Manual or I2C)
Frequently asked questions
How does Industrial Trading differ from its competitors?

Is there a warranty for the iMP?

Which carrier will Industrial Trading use to ship my parts?

Can I buy parts from Industrial Trading if I am outside the USA?

Which payment methods does Industrial Trading accept?

Why buy from GID?

Quality
We are industry veterans who take pride in our work

Protection
Avoid the dangers of risky trading in the gray market

Access
Our network of suppliers is ready and at your disposal

Savings
Maintain legacy systems to prevent costly downtime

Speed
Time is of the essence, and we are respectful of yours
Related Products

Emerson 00375-0003-0011 375 Field Communicator Spare Power Supply/Charger (90-240 VAC, 50/60Hz, US/U...

Emerson LCC250-12U-4P Power Supply - 12 V output, ±10% adjustment range, 0 A min /20.8 A max output ...

Emerson LCC250-12U-4PE Power Supply - 12 V output, ±10% adjustment range, 0 A min /20.8 A max output...

Emerson LCC250-12U-7P Power Supply - 12 V output, ±10% adjustment range, 0 A min /20.8 A max output ...
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods