DANAHER SX210A6
Specifications
Approvals
UL Recognition E96337 | CSA Certification LR26861
Operating Temperature
+32° to +122°F (0° to +50°C)
Operating Voltage/Frequency
A6 - 120 VAC, 50/60 Hz B6 - 240 VAC, 50/60 Hz
Output Rating
Relay: 5 amp (resistive), 10 to 264 VAC Current capacity derates from 7 amps at 250C to 5 amps at 500C with all output contacts used
Power on Response
200 ms max.
Repeat Accuracy
±0.001% of setting or 35 ms, whichever is larger
Reset Time
15 ms
Setting Accuracy
±0.05% of setting or 50 ms, whichever is larger
Static Discharge
Unit function is unaffected by a constant 3600 volt peak, 60 Hz discharge applied to the grounded front plate at a relative humidity of less than 25%
Transient Protection
Immune to 2500 volts peak transients up to 50 microseconds in duration
Vibration
Unit function is unaffected by 2.5G sinusoidal vibration magnitude in both directions of the perpendicular mounting axes imposed from 10 to 100 Hz
Features
- Eight programmable time ranges and eight output operating modes
- Flashing LED (right side of display) indicates unit is in timing cycle and LED (left side of display) lights when programmed contacts are energized
- Four .3 inch red LED displays for easy readability
- Keypad "lock" function allows setpoint to be viewed, but does not allow unauthorized changes
- NEMA 4 Hosedown Test rated
- Nonvolatile RAM memory retains setpoint, actual time values, and program parameters (10 year expected life of data in memory)
- Operating modes and all other setup functions programmed with miniature rocker switches located on the back of the housing
- Programming changes entered via increment and decrement keys
- SET and ENT keys provide access to setpoint and front panel programmed functions
- Special surface just below the display on which the function can be marked with pen or pencil
- Two DPDT relay outputs with five amp contact ratings - one is a set of instantaneous contacts that energize when timing cycle starts and remain energized until timer is reset, and the other is a set o
- Two removable terminal blocks with screw gate style wire clamps permit prewiring of panel without the timer in place and eliminate rewiring if unit needs to be removed or replaced
Datasheet
DANAHER=SX210A6=datasheet1-366507943.pdf
50 KiB
Extracted Text
EAGLE SIGNAL brand SX210 Microprocessor Digital Timer Electronic Timers Economical, electronic, single setpoint reset timer... with 8 time ranges and 8 operating modes ® ® 5 RECOGNIZED CERTIFIED E L T E The SX210 timer is a microprocessor based digital timer housed in a SPECIFICATIONS I C standard DIN style case (68mm square cutout). The small case and M T Time Ranges: front bezel require minimal panel space yet provide large, easy to use E R programming keys and a .3 inch high LED display. R O Sym. Maximum Minimum S T NEight programmable time ranges and eight output operating modes Range Setting I I MOperating modes and all other setup functions programmed with C 1 99.99 Sec. .01 Sec. E miniature rocker switches located on the back of the housing 2 999.9 Sec. .1 Sec. R Nonvolatile RAM memory retains setpoint, actual time values, and S 3 99.99 Min. .01 Min. program parameters (10 year expected life of data in memory) 4 999.9 Min. .1 Min. NEMA 4 Hosedown Test rated 5 99.99 Hr. .01 Hr. Special surface just below the display on which the function can be 6 999.9 Hr. .1 Hr. marked with pen or pencil 7 99 Min.: 59 Sec. 1 Sec. SET and ENT keys provide access to setpoint and front panel 8 99 Hr.: 59 Min. 1 Min. programmed functions Programming changes entered via increment and decrement keys Operating Voltage/Frequency: A6 - 120 VAC, 50/60 Hz Keypad "lock" function allows setpoint to be viewed, but does not B6 - 240 VAC, 50/60 Hz allow unauthorized changes Setting Accuracy: ±0.05% of setting or 50 ms, whichever is largerFour .3 inch red LED displays for easy readability Flashing LED (right side of display) indicates unit is in timing cycle Repeat Accuracy: ±0.001% of setting or 35 ms, whichever is larger and LED (left side of display) lights when programmed contacts are Reset Time: 15 ms energized Power on Response: 200 ms max.Two removable terminal blocks with screw gate style wire clamps permit prewiring of panel without the timer in place and eliminate Operating Temperature: +32˚ to +122˚F (0˚ to +50˚C) rewiring if unit needs to be removed or replaced Output Rating: Relay: 5 amp (resistive), 10 to 264 VAC Two DPDT relay outputs with five amp contact ratings - one is a set Current capacity derates from 7 amps at 250C to 5 amps at 500C with all of instantaneous contacts that energize when timing cycle starts and output contacts used remain energized until timer is reset, and the other is a set of programmable contacts that can be programmed to turn on and off Vibration: Unit function is unaffected by 2.5G sinusoidal vibration magni- in several operating modes tude in both directions of the perpendicular mounting axes imposed from 10 to 100 Hz Static Discharge: Unit function is unaffected by a constant 3600 volt peak, 60 Hz discharge applied to the grounded front plate at a relative humidity of less than 25% Transient Protection: Immune to 2500 volts peak transients up to 50 microseconds in duration Approvals: UL Recognition E96337 CSA Certification LR26861 5.14 DANAHER INDUSTRIAL CONTROLS OUTPUT OPERATING MODES Interval Operation ON-Delay Operation INSTANTANEOUS CONTACT OPERATION INSTANTANEOUS CONTACT OPERATION START INPUT START INPUT RESET RESET PROGRAMMED PROGRAMMED TIMING CONTACTS CONTACTS RESET TIMING Interval Operation with Time Totalization ON-Delay Operation with Time Totalization The contacts operate as they do in the ON-Delay mode above. The contacts operate as they do in the Interval mode above. The contacts are energized during the timing cycle and deenergize at the When the timing cycle is completed and the programmed contacts end of the timing cycle. When the timing cycle is completed and the are energized, the SX210 timer begins time totalizing and continues programmed contacts are deenergized, the SX210 timer begins time until the unit is reset. totalizing and continues until the unit is reset. Single-Pulse Operation 5 WIRING INSTANTANEOUS CONTACT OPERATION START INPUT T E 1 2 RESET O L PROGRAMMED T E T 15 CONTACTS PULSE I C TIME A TIMING M T 8 L E R 6 R I O 3 S Pulse and Repeat Operation Z N 7 4 I I INSTANTANEOUS CONTACT OPERATION C 9 N 5 START INPUT 14 G RESET 13 11 PROGRAMMED 10 PULSE PULSE CONTACTS INSTANTANEOUS 12 TIMING TIMING CONTACTS PROGRAMMED CONTACTS MOUNTING The SX210 timer uses two removable mounting clips with adjustable screws to mount the enclosure in a panel as shown below. To mount the unit, slide the gasket onto the case until it is against the back of the bezel and place the unit in the panel cutout from the front of the panel. 5.00 2.98 0.23 (75.69) (5.84) (127.0) yyyyy PANEL CUTOUT 2.98 +0.028 (75.69) 2.72 -0.000 +0.7 (68 ) -0.0 SQUARE yyyyyyy yyyyyyy PANEL THICKNESS (STEEL) 0.50 REQUIRED 0.125 – 0.313 (3.125 – 7.825) FOR WIRING yy ORDERING INFORMATION SX2 10 A6 OUTPUT TYPE VOLTAGE & FREQUENCY Sym. Description Sym. Description 10 Relay Output A6 120 VAC, 50/60 Hz B6 240 VAC, 50/60 Hz DANAHER INDUSTRIAL CONTROLS 5.15
Frequently asked questions
How does Industrial Trading differ from its competitors?
Is there a warranty for the SX210A6?
Which carrier will Industrial Trading use to ship my parts?
Can I buy parts from Industrial Trading if I am outside the USA?
Which payment methods does Industrial Trading accept?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods