HS-5200/5000 ® TM Half Pentium MMX L/VGA I.S.B. •Half Size All-in-one with VGA CRT-LCD Interface• •WDT•DOC•CTA•USB•IrDA•COM-1/2•PPI• •PISA/ISA Bus Industrial Single Board Computer• HS-5200P/5000P ® TM Half Pentium MMX I.S.B. •Half Size All-in-one • •WDT•DOC•CTA•USB•IrDA•COM-1/2•PPI• •PISA/ISA Bus Industrial Single Board Computer• Copyrights This manual is copyrighted and all rights are reserved. It is not allow any non authorization in copied, photocopied, translated or reproduced to any electronic or machine readable form in whole or in part without prior written consent from the manufacturer. In general, the manufacturer will not be liable for any direct, indirect, special, incidental or consequential damages arising from the use of inability to use the product or documentation, even if advised of the possibility of such damages. The manufacturer keeps the rights in the subject to change the contents of this manual without prior notices in order to improve the function design, performance, quality and reliability. The author assumes no responsibility for any errors or omissions, which may appear in this manual, nor does it make a commitment to update the information contained herein. Trademarks BOSER is a registered trademark of BOSER Technology Co., Ltd. Award is a registered trademark of Award Software, Inc. ISB is a registered trademark of BOSER Technology Co., Ltd. All other trademarks, products and or product's name mentioned herein are mentioned for identification purposes only, and may be trademarks and/or registered trademarks of their respective companies or owners. © Copyright 1999 All Rights Reserved. User Manual edition 1.8, Jan 17, 2002 Contents HS-5200/5000 ...................................................................1 HS-5200P/5000P ........................................................1 GENERAL INFORMATION .............................................................................3 1.1 MAJOR FEATURES .....................................................................................4 1.2 SPECIFICATIONS.........................................................................................5 1.3 DELIVERY PACKAGE...................................................................................6 HARDWARE INSTALLATION ........................................................................7 2.1 CAUTION OF STATIC ELECTRICITY.............................................................7 2.2 CAUTION ON UNPACKING AND BEFORE INSTALLATION .............................8 2.3 HS-5200/5000’S LAYOUT.........................................................................9 2.4 QUICK LISTING OF JUMPERS ...................................................................10 2.5 QUICK LISTING OF CONNECTORS............................................................10 2.6 JUMPER SETTING DESCRIPTION..............................................................11 2.7 SETTING THE CPU...................................................................................12 2.8 CMOS DATA CLEAR ...............................................................................14 2.9 SYSTEM MEMORY DRAM........................................................................15 2.10 WATCH-DOG TIMER...............................................................................15 2.11 VGA CONTROLLER ( HS-5200, HS-5000 ONLY )...............................17 2.12 DISKONCHIP ADDRESS SETTING.......................................................18 2.13 CPU TEMPERATURE ALARM.................................................................18 2.14 ON BOARD MULTI-I/O SETTING ............................................................19 2.15 BIOS TYPE SELECTION.........................................................................19 2.16 CACHE RAM MODE SELECTION ...........................................................19 CONNECTION .................................................................................................21 3.1 THE FLOPPY DISK DRIVE CONNECTOR...................................................21 3.2 PCI E-IDE DRIVE CONNECTOR..............................................................22 3.3 PARALLEL PORT CONNECTOR.................................................................22 3.4 SERIAL PORTS CONNECTORS .................................................................24 3.5 KEYBOARD CONNECTORS .......................................................................25 3.6 POWER'S LED, KEY-LOCK AND RESET BUTTON ....................................25 3.7 EXTERNAL SPEAKER................................................................................26 Contents • i 3.8 PS/2 MOUSE 6-PIN MINI-DIN CONNECTOR ...........................................26 3.9 VGA CONNECTORS ( HS-5200, HS-5000 ONLY ) ................................27 3.10 IR CONNECTOR .....................................................................................27 3.11 EXTRA POWER CONNECTOR.................................................................28 3.12 USB PORTS CONNECTOR.....................................................................28 3.13 FLAT-PANEL CONNECTOR ( HS-5200, HS-5000 ONLY ) ....................29 AWARD BIOS SETUP....................................................................................30 4.1 MAIN MENU..............................................................................................31 4.2 STANDARD CMOS SETUP.......................................................................32 4.3 BIOS FEATURES SETUP..........................................................................33 4.4 CHIPSET FEATURES SETUP.....................................................................34 4.5 INTEGRATED PERIPHERALS .....................................................................35 4.6 POWER MANAGEMENT SETUP.................................................................36 ii •Contents Chapter-1 General Information This is a common manual of HS-5200, HS-5200P, HS-5000 and HS-5000P series Industrial Single Board CPU Card. The descriptions herein are subject to HS-5200. The HS-5200P, which is based on HS-5200 but without VGA CRT-LCD, supports. The HS-5000 is based on HS-5200 but supports with ISA bus which without PCI interface at slot. The HS-5000P, which is based on HS-5000 but without VGA CRT-LCD supports. The HS-5200/5000 is a PISA/ISA bus Industrial Single Board (I.S.B.) CPU card with features combine together to make it an ideal all-in-one industrial single board computer, enhanced I/O effects, VGA and support panel functions and make it an excellent choice for display-intensive applications. Various panel of LCD types support including TFT, monochrome STN, EL and many others. The HS-5200/5000 also provides a 10-pin header internal VGA connector for monitor built-in system. The HS-5200 supports BEDO, EDO and FPM DRAM sockets. This gives you the flexibility of configuring your system from 1 to 128 MB DRAM by using the most economical SIMMs. It also provides two 72-pin SIMM sockets for its on-board system DRAM. The advanced PISA bus add-on connection of HS-5200/5000 allows user could easily obtain both ISA's 16-bit and PCI's 32-bit full set signals from a small 16-bit PISA slot for suitable plug into a small size system with 8/16/32-bit operating. A single Flash chip holds the system BIOS, and you can change the Flash BIOS by the Utility Update. Advanced USB and IR ports also provide a faster data transmission. The HS-5200/5000 features include a temperature-warning sensor installed under the CPU socket. The sensor monitors the CPU temperature and generates a warning buzzer in response to the temperature increases that may cause a system malfunctions. You can also use the DOS version of the "DiskOnChip" socket by issuing commands from the DOS prompt without the necessity of other software supports. The "DiskOnChip" supports up to 72 MB. If a un-expect program cause halts, the watchdog timer will automatically reset the CPU or generate an interrupt. The watchdog is designed for pure hardware and doesn’t need any arithmetical functions of a real-time clock chip. This ensures the reliability in an unmanned or standalone system. 3 1.1 Major Features � HS-5200/5000, HS-5200/5000P PISA bus supported. HS-5000, HS-5000P ISA bus supported. ® � Intel MMX™/Pentium CPU 75〜233 MHz, AMD k5, k6, k6-2 333MHz, 350MHz, Cyrix 6x86, M2 300MHz. � SiS 5571 chipset supports EDO or FastPage DRAM up to 128 MB. � Fast PCI enhanced IDE controller supports four IDE drives (large hard disks, CD-ROM, tape backup … etc.) � PnP I/O address & IRQ selection. � Two high-speed serial RS-232 Ports supports 16C550 UART with 16-byte FIFO. � One enhanced bi-directional parallel port. Supports SPP/EPP/ECP. � On board keyboard and PS/2 Mouse connector. � On board SMC 37C669 super I/O. � On board 32 bit PCI-BUS SVGA/ Panel controller. ( HS-5200/5000, HS-5000 only ) � "DiskOnChip™" Socket Supported Memory Size up to 72 MB. � Switch Power Regulator � CPU Temperature Alarm supported. 4 1.2 Specifications ® � CPU: Intel MMX™/Pentium 75~233MHz, AMD k5, k6, k6-2 350MHz, Cyrix 6x86,M2 300MHz. � Bus interface: PISA bus ( HS-5200, HS-5200P ) ISA bus ( HS-5000, HS-5000P ) � Chipset: SiS 5571 � Data bus: 64-bit � Processing ability: 64-bit � Flat panel / CRT SVGA Controller: CHIP 65550 (HIQV32) Chipset with 1 MB memory support to color and monochrome Single Drive (SS) and Dual Drive (DD) STN, TFT & EL panels. Support CRT resolutions up to 1024x768 256 colors. ( HS-5200 and HS-5000 only ) � PCI Enhanced IDE interfaces: Supports up to four IDE devices support mode 3, 4 hard Disk, and data transfer rate up to 16.6 MB/sec minimum. � RAM memory: Up to 128MB uses two 72-pin SIMM sockets; supports BEDO, EDO and FastPage DRAM. � Cache memory: 512KB Pipeline burst cache memory. � Floppy disk drive interface: Supports up to two floppy disk drives. � Parallel port: One bi-directional parallel port. Supports SPP/ECP/EPP mode. � Serial port: Two RS-232 ports. Both provide 16C550 UART with 16-byte FIFO. � BIOS: AWARD Y2K flash BIOS. � Watchdog timer: Hardware circuit can be set by 1, 2, 10, 20, 110, or 220 seconds period Reset or NMI were generated when CPU did not periodically trigger the timer. � DMA channels: 7 � Interrupt levels: 15 � Keyboard: 6-pin mini DIN connector or 5-pin header supports standard PC/AT keyboard. � Mouse: 6-pin mini DIN support PS/2 mouse. � USB: Supports 2 USB header. � IR interface: Supports one lrDA TX/RX header. � Flash memory Disk: Reserved socket for "DiskOnChip™", support up to 72MB Flash memory disk. 5 � Extra Power: Supports 8-PIN extra DC power input connector. � CMOS: Real-time clock/calendar and battery backup by DS12B887 or equivalent device. � CPU Temperature Alarm: Hardware circuit design via beeping alarm when CPU's temperature is over heating 55°C±5°C limited. � Power supply voltage: +5V (4.75 to 5.25V), +12V / -12V power supply. � Max. Power requirement: +5V @6A, +12V/-12V @20mA. � Operating temperature: 0-55°C (CPU need cooler). � Board size: HS-5200, HS-5200P 7.3"(L) x 5" (W) (185mm x 127mm). HS-5000, HS-5000P 7.3"(L) x 4.8" (W) (185mm x 122mm). 1.3 Delivery Package The delivery package includes all following items: ✲ One Industrial Single Board CPU Card ✲ One Printer & COM2 Bracketed Flat Cable ✲ Two IDE port Flat Cables ✲ FDD port Flat Cable ✲ COM port Cable ✲ One PS/2 Mouse to Standard Keyboard Cable ✲ VGA Utility Diskette (HS-5200, HS-5000 only) ✲ User’s Manual Please contact with your dealer if any of these items are missing or damaged when purchasing. And please keep all parts of the delivery package with packing materials in case of you want to ship or store the product in feature. 6 Chapter-2 Hardware Installation This chapter provides the information on how to install the hardware. At first, please follow up sections 1.3, 2.1 and 2.2 in check the delivery package and carefully unpacking. Following after, the jumpers setting of switch, watchdog timer, and the DiskOnChip address selection. 2.1 Caution of Static Electricity The CPU Card has been well package with an anti-static bag in protect its sensitive computer components and circuitry from the damage of static electric discharge. Note: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC PROTECTION. You should follow the steps as following to protect the board in against the static electric discharge whenever you handle the board: 1. Please use a grounding wrist strap on whoever needs to handle the CPU Card. Well clip the ALLIGATOR clip of the strap to the end of the shielded wire lead from a grounded object. Please put on and connect the strap before handles the CPU Card for harmlessly discharge any static electricity through the strap. 2. Please use anti-static pad for put any components or parts or tools on the pad whenever you work on them outside the computer. You may also in use the anti-static bag instead the pad. Please ask from your local supplier in help up your necessary parts on anti-static requirement. 7 2.2 Caution on Unpacking and Before Installation First of all, please follow with all necessary steps of section 2.1 in protection the CPU Card from electricity discharge. With refer to section 1.3, please check the delivery package again with following steps: 1. Unpacking the CPU Card, keep well storage of all packing material, manual and diskette etc. if has. 2. Is there any components lose or drop from the board? DO NOT INSTALL IF HAPPENED. 3. Is there any visual damaged of the board? DO NOT INSTALL IF HAPPENED. 4. Well check from your optional parts (i.e. CPU, SRAM, DRAM, ROM-Disk etc.) for completed setting all necessary jumpers setting to jumper pin-set and CMOS setup correctly. Please also reference to all information of jumpers setting in this manual. 5. Well check from your external devices (i.e. Add-On-Card, Driver Type etc.) for completed add-in or connection and CMOS setup correctly. Please also reference to all information of connector connection in this manual. 6. Please keep all necessary manual and diskette in a good condition for your necessary re-installation if you change your Operating System or whatever needs. 8 2.3 HS-5200/5000’s Layout Default Setting：JP12 1-2 ON for HS-5000 JP12 1-2, 7-8 ON for HS-5200 9 2.4 Quick Listing of Jumpers JP 3, 4, 5 — for CPU type setting JP 10 — for Cache RAM mode setting JP 13 — Type setting of Flash BIOS JP 14 — CMOS Data Clear JP 15 — for DiskOnChip™ address setting JP 12 — CPU's Vcore voltage level selection setting JP 9 — CPU's operating voltage selection setting JP 22, 23, 24 — System PLL clock setting JP 16 — System Clock selection JP 17 — WATCH-DOG Time-out period selection JP 18 — WATCH-DOG Active selection JP 19 — On-Board I/O Enable & Disable control JP 25 — CPU Temperature Alarm control 2.5 Quick Listing of Connectors CN1: KEYLOCK CN2: FLAT-PANEL CONNECTOR ( HS-5200, HS-5000 only ) CN3: 1st HDD (IDE) CONNECTOR CN4: 2nd HDD (IDE) CONNECTOR CN5: COM2 (HEADER 5x2) CN6: USB0 CONNECTOR CN7: USB1 CONNECTOR CN8: PARALLEL PORT CN9: 5P KEYBOARD CONNECTOR CN10: FDD CONNECTOR CN11: INTERNAL VGA 10-PIN CONNECTOR ( HS-5200, HS-5000 only ) CN12: IR CONNECTOR CN13: 8P POWER CONNECTOR CN14: EXTERNAL VGA CONNECTOR (DB15) ( HS-5200, HS-5000 only ) CN15: MINI-DIN 6-PINS MOUSE CONNECTOR (PS/2) CN16: COM1 (DB9) CN17: MINI-DIN 6-PINS KEYBOARD CONNECTOR (PS/2) JP6: RESET BUTTON CONNECTOR JP7: SPEAKER CONNECTOR JP8: IDE LED CONNECTOR 10 2.6 Jumper Setting Description A jumper pin-set is ON as a shorted circuit with a plastic cap inserted over two pins. A jumper pin-set is OFF as a open circuit with a plastic cap inserted over one or no pin(s) between pins. The below figure 2.2 shows the examples of different jumper pin-set setting as ON or OFF in this manual. Figure 2.2 All jumper pin-set already has its default setting with the plastic cap inserted as ON, or without the plastic cap inserted as OFF. The default setting may reference in this manual with a " * " symbol in front of the selected item. 11 2.7 Setting the CPU All CPU Card provides all possibility in jumper setting for wide using all types of CPU with JP3, JP4, JP5, JP16, JP22, JP23 and JP24 setting in following. The JP1 sets the multi-times ratio of the CPU’s specification. Please reference to the following table for all type CPU in used. � CPU’s Clock Ratio select Clock Ratio BF2 BF1 BF0 Intel AMDJP4JP5JP3 P54C P55C K6 1-2 1-2 1-2 2.5 2.5 *2.5 OFF ON ON 3.0 3.0 3.0 OFF ON OFF 2.0 2.0 2.0 OFFOFF ON 1.5 3.5 3.5 OFFOFFOFF 2.5 2.5 4.5 ON ON ON 3.0 3.0 5.0 ON ON OFF 1.5 2.0 4.0 ON OFF ON 2.5 3.5 5.5 ON OFFOFF *) : default setting JP16 used to setting the System clock base rate. The System clock setting will preset the system operating clocking base rate. � System Clock select JP16 (System 1-2 3-4 5-6 Clock) 50 MHz ON ON OFF 55 MHz OFF OFF ON 60 MHz ON OFF OFF *66 MHz OFF ON OFF 75 MHz ON OFF ON *) : default setting 12 � CPU Vcore Voltage Selection Correspond to different type CPU, it is request to set JP12 for match the CPU's Vcore operating voltage. Here shows at below of the proper jumper settings for their respective Vcore at range 2.0V to 3.5V. Voltage HS-5200 HS-5000 2.0V ALL OFF 2.1V 7-8 2.2V 5-6 5-6, 7-8 2.3V 5-6, 7-8 2.4V 3-4 2.5V 3-4, 7-8 7-8 2.6V 3-4, 5-6 2.7V 3-4, 5-6, 7-8 2.8V 1-2 *2.9V * 1-2, 7-8 * 5-6 3.0V 1-2, 5-6 3.1V 1-2, 5-6, 7-8 3.2V 1-2, 3-4 3.3V 1-2, 3-4, 7-8 ALL OFF 3.4V 1-2, 3-4, 5-6 1-2 3.5V 1-2, 3-4, 5-6, 7-8 3-4 *) : default setting For single or dual power type CPU, please set a correct to jumper JP9 as following table. � CPU Operating Voltage Selection CPU Type JP9 P54,P55 2-3 *P55C Dual Voltage 1-2 *) : default setting 13 The JP22, 23, 24 used to setting the system PLL clock rate for meet with the best feature of I/O interface performance. Please set the clock rate at a necessary operating condition. An over specification setting will cause the system malfunction or un-stateable. � PLL Clock setting PLL Clock JP22 JP23 JP24 50 MHz 1-2 2-3 1-2 60 MHz 1-2 1-2 2-3 *66 MHz 2-3 1-2 2-3 75 MHz 1-2 2-3 2-3 *) : default setting The above default setting of JP3, JP4, JP5, JP9, JP12, JP16, JP22, JP23 and JP24 show a AMDK6-166(2.9V) CPU in used. ( i.e. 66.6 x 2.5 ≈ 166 MHz ). Please contact with your CPU supplier for detail specification in correcting selected setting of all. 2.8 CMOS Data Clear The JP14 provides a hardware CMOS data clear function with an ON to it. Never clear CMOS data during power on in case of damage the sensitive electronic components or the board. � CMOS Data Clear (Only for DS12B887) JP14 DESCRIPTION ON Clear Data *OFF Normal 14 2.9 System Memory DRAM All CPU Card provides a wide range on-board DRAM memory by two pieces SIMM sockets (Bank0 & Bank1) to accept 1 MB, 2MB, 4MB, 8MB, 16MB, 32MB or 64MB. The SIMMs (Single In-Line Memory Modules) RAM request the access time should be 70 n-second or faster. The total capacity of the on board memory are between 2MB to 128MB. See the figure on section 2.3 for get the identifying the banks. Please take notes that the memory capacity of both SIMMs should be the same. The Card requires at least 2pcs of the RAM modules on SIMM socket. 2.10 Watch-Dog Timer There are three access cycles of Watch-Dog Timer as Enable, Refresh and Disable. The Enable cycle should proceed by READ PORT 443H. The Disable cycle should proceed by READ PORT 043H. A continue Enable cycle after a first Enable cycle means Refresh. Once if the Enable cycle activity, a Refresh cycle is request before the time-out period for restart counting the WDT Timer's period. Otherwise, it will assume that the program operation is abnormal when the time counting over the period preset of WDT Timer. A System Reset signal to start again or a NMI cycle to the CPU comes if over. The JP18 is using for select the active function of watch-dog timer in disable the watch-dog timer, or presetting the watch-dog timer activity at the reset trigger, or presetting the watch-dog timer activity at the NMI trigger. � JP18 : Watch-Dog Active Type Setting JP18 DESCRIPTION *1-2 System Reset 2-3 Active NMI OFF disable Watch-dog timer 15 � JP17 : WDT Time - Out Period PERIOD 1-2 3-4 5-6 7-8 *1 sec OFF OFF ON OFF 2 sec OFF OFF ON ON 10 sec OFF ON OFF OFF 20 sec OFF ON OFF ON 110 sec ON OFF OFF OFF 220 sec ON OFF OFF ON The Watch-dog timer is disabled after the system Power-On. The watch-dog timer can be enabled by a Enable cycle with reading the control port (443H), a Refresh cycle with reading the control port (443H) and a Disable cycle by reading the Watch-dog timer disable control port (043H). After a Enable cycle of WDT, user must constantly proceed a Refresh cycle to WDT before its period setting comes ending of every 1, 2, 10, 20, 110 or 120 seconds. If the Refresh cycle does not active before WDT period cycle, the on board WDT architecture will issue a Reset or NMI cycle to the system. The Watch-Dog Timer is controlled by two I/O ports. 443H I/O Read The Enable cycle. 443H I/O Read The Refresh cycle. 043H I/O Read The Disable cycle. The following sample programs showing how to Enable, Disable and Refresh the Watch-dog timer: WDT_EN_RF EQU 0443H WDT_DIS EQU 0043H WT_Enable PUSH AX ; keep AX DX PUSH DX MOV DX,WDT_EN_RF ; enable the watch-dog timer IN AL,DX POP DX ; get back AX, DX POP AX RET 16 WT_Refresh PUSH AX ; keep AX, DX PUSH DX MOV DX,WDT_ET_RF ; refresh the watch-dog timer IN AL,DX POP DX ; get back AX, DX POP AX RET WT_DISABLE PUSH AX PUSH DX MOV DX,WDT_DIS ; disable the watch-dog timer IN AL,DX POP DX ; get back AX, DX POP AX RET 2.11 VGA Controller ( HS-5200, HS-5000 only ) The C&T 655xx family supports a wide variety of monochrome and color Single-Panel, Single-Drive (SS) and Dual-Panel, Dual Drive (DD) standard and high-res passive STN and active matrix TFT/MIN LCD, and EL panels. For monochrome panels, up to 64 gray scales are supported. Up to 4096 different colors can be displayed on passive STN LCDs and up to 16M colors on 24-bit active matrix LCDs. The CPU Card uses C&T 65550 chipset. Provides 2.0 mm pitch 44-pin on-board internal connector for flat panel connection; and a external DB15 analogy R.G.B. output connector for CRT monitor. By BIOS setup, user may use one of the display devices or both. Please use at the same resolution when both display. Please contact with your dealer if connection to a new specification flat panel. The CPU Card offers a variety of programmable features to optimize display quality. Vertical centering and stretching are provided for handling modes with less than 480 lines on 480 - line panels. Horizontal and vertical stretching capabilities are also available for both text and graphics modes for optimal display of VGA text and graphics modes on 800x600 and 1024x768 panels. 17 2.12 DiskOnChip Address Setting All CPU Card provides a U10 socket for install the DiskOnChip module. A JP15 may select the starting memory address of the DiskOnChip (D.O.C.) for avoid the mapping area with any other memory devices. If you have another extra memory devices in the system with the same memory, neither the CPU Card nor the extra memory devices will function normally. Please setting both at different memory address mapping. � JP15 : DiskOnChip Address JP15 Address *1-2 D000 3-4 D800 *) : default setting The D.O.C. function allows the system in using without FDD nor HDD. The D.O.C. may formatting as driver C: or driver A:. User may also easily uses the DOS's commands such as FORMAT, SYS, COPY, XCOPY, DISCOPY and DISKCOMP etc. This is means that the D.O.C. may uses as driver-A if the system without FDD-A for ambient application. Please contact with your supplier for different size D.O.C. module. 2.13 CPU Temperature Alarm All CPU Card provides the feature of CPU temperature alarm. The warning buzzer will alarm when the CPU's temperatures rise over to 55±5℃. The warning buzzer will shout off automatically until the temperatures goes under 55±5℃. The JP25 provides for disable or enable the alarm function. � JP25 : CPU Temperature Alarm Control 18 JP25 DESCRIPTION *ON Enable OFF Disable *) : default setting 2.14 On Board Multi-I/O Setting All CPU Card provides a JP19 for enable or disable the on-board multi-I/O chipset when application of CPU temperature alarm. An Enable means that the CPU Card using the on-board multi-I/O chipset. A Disable means that the CPU Card doesn't using the on-board multi-I/O chipset. User may use their I/O interface card when JP19 selects Disable. � JP19 : On Board Multi-I/O Chipset Enable/Disable Selection JP19 Address *OFF Enable ON Disable *) : default setting 2.15 BIOS Type Selection All CPU Card provides a JP13 for selects the type of flash chip in using as the BIOS. The manufacturer provides 29C010 on the board. � JP13 : BIOS Type Selection JP13 Address *1-2 29C010 2-3 28F010 *) : default setting 2.16 Cache RAM Mode Selection All CPU Card provides a JP10 for selects the type of cache RAM mode in using. The manufacturer provides WB on the board. 19 � JP10 : Cache RAM Mode Selection JP10 Address *OFF WB ON WT 20 Chapter-3 Connection This chapter gives all necessary information of the peripheral's connections, switches and indicators. 3.1 The Floppy Disk Drive Connector A standard 34-pin header daisy-chain driver connector provides as CN10 with following pin assignment. Total two FDD drivers may connect. � CN10 : FDD CONNECTOR PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 GROUND 2 REDUCE WRITE 3 GROUND 4 N/C 5 GROUND 6 N/C 7 GROUND 8 INDEX# 9 GROUND 10 MOTOR ENABLE A# 11 GROUND 12 DRIVE SELECT B# 13 GROUND 14 DRIVE SELECT A# 15 GROUND 16 MOTOR ENABLE B# 17 GROUND 18 DIRECTION# 19 GROUND 20 STEP# 21 GROUND 22 WRITE DATA# 23 GROUND 24 WRITE DATA# 25 GROUND 26 TRACK 0# 27 GROUND 28 WRITE PROTECT# 29 GROUND 30 READ DATA# 31 GROUND 32 SIDE 1 SELECT 33 GROUND 34 DISK CHANGE# 21 3.2 PCI E-IDE Drive Connector Two standard 40-pin header daisy-chain driver connectors provide as CN3 & CN4 with following pin assignment. Total four IDE (Integrated Device Electronics) drivers may connect. CN3(IDE 1) : Primary IDE Connector CN4(IDE 2) : Secondary IDE Connector � CN3/CN4 : IDE Interface Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 RESET 2 GROUND 3 DATA 7 4 DATA 8 5 DATA 6 6 DATA 9 7 DATA 5 8 DATA 10 9 DATA 4 10 DATA 11 11 DATA 3 12 DATA 12 13 DATA 2 14 DATA 13 15 DATA 1 16 DATA 14 17 DATA 0 18 DATA 15 19 GROUND 20 N/C 21 N/C 22 GROUND 23 IOW# 24 GROUND 25 IOR# 26 GROUND 27 N/C 28 BALE - DEFAULT 29 N/C 30 GROUND# -DEFAULT 31 INTERRUPT 32 IOCS16#-DEFAULT 33 SA1 34 N/C 35 SA0 36 SA2 37 HDC CS0 38 HDC CS1# 39 HDD ACTIVE 40 GROUND 3.3 Parallel Port Connector A standard 26-pin flat cable driver connector provides as CN8 with following pin assignment for connection to parallel printer. 22 � CN8 : Parallel Port Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 STROBE 2 DATA 0 3 DATA 1 4 DATA 2 5 DATA 3 6 DATA 4 7 DATA 5 8 DATA 6 9 DATA 7 10 ACKNOWLEDGE 11 BUSY 12 PAPER EMPTY 13 PRINTER SELECT 14 AUTO FORM FEED 15 ERROR# 16 INITIALIZE 17 PRINTER SELECT LN# 18 GROUND 19 GROUND 20 GROUND 21 GROUND 22 GROUND 23 GROUND 24 GROUND 25 GROUND 26 GROUND 23 3.4 Serial Ports Connectors All CPU Card offers two high speed NS16C550 compatible UARTs with Read/Receive 16 byte FIFO serial ports with one DB-9 external connector, and one internal 10-pin header connector. � CN16 : Serial Port DB-9 Connector (ACE0) PIN NO. DESCRIPTION 1 DATA CARRIER DETECT (DCD) 2 RECEIVE DATA (RXD) 3 TRANSMIT DATA (TXD) 4 DATA TERMINAL READY (DTR) 5 GROUND (GND) 6 DATA SET READY (DSR) 7 REQUEST TO SEND (RTS) 8 CLEAR TO SEND (CTS) 9 RING INDICATOR (RI) � CN5 : Serial Port 10-pin Header (ACE1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 DCD 2 DSR 3 RXD 4 RTX 5 TXD 6 CTX 7 DTR 8 RI 9 GND 10 NC 24 3.5 Keyboard Connectors All CPU Card offers two possibilities for keyboard connections to external PS/2 type keyboard at CN17, or an internal 5-pin header at CN9. � CN9 : 5-pin Header Keyboard Connector PIN NO. DESCRIPTION 1 KEYBOARD CLOCK 2 KEYBOARD DATA 3 N/C 4 GROUND 5 +5V � CN17 : 6-pin Mini-DIN Keyboard Connector PIN NO. DESCRIPTION 1 KEYBOARD DATA 2 N/C 3 GROUND 4 +5V 5 KEYBOARD CLOCK 6 N/C 3.6 Power's LED, Key-Lock and Reset Button The following provides the pin information for Power's LED indicator, Key-Lock and Reset Button connections from CN1, JP6 and JP8. � CN1 : POWER LED & KEYLOCK PIN NO. DESCRIPTION 1 POWER LED ANODE 2 NC 3 GROUND 4 KEYLOCK 5 GROUND 25 � JP6 : RESET BUTTON PIN NO. DESCRIPTION 1 EXTERNAL RESET 2 GROUND � JP8 : IDE LED connector PIN NO. DESCRIPTION 1 +5V 2 HDD ACTIVE# 3.7 External Speaker All CPU Card has an on-board buzzer. And it also provides the JP7 in allows user to connecting to the external speaker. � JP7 : Speaker Connector PIN NO. DESCRIPTION 1 SPEAKER SIGNAL 2 NC 3 GROUND 4 +5V 3.8 PS/2 Mouse 6-pin Mini-DIN Connector All CPU Card provides an external PS/2 mouse connector at CN15 with following pin information. � CN15 : PS/2 Mouse Connector PIN NO. DESCRIPTION 1 DATA 2 NC 3 GROUND 4 +5V 5 CLK 6 NC 26 3.9 VGA Connectors ( HS-5200, HS-5000 only ) The CPU Card provides two possible VGA connections. One standard DB-15 external VGA connector as following CN14 pin information. Another internal 10-pin header as following CN11 pin information. � CN14 : 15-pin DB-15 Female VGA connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 RED 2 GREEN 3 BLUE 4 NC 5 GROUND 6 GROUND 7 GROUND 8 GROUND 9 NC 10 GROUND 11 NC 12 NC 13 HSYNC 14 VSYNC 15 NC � CN11 : 10-pin internal VGA Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 RED 2 GROUND 3 GREEN 4 GROUND 5 BLUE 6 GROUND 7 HSYNC 8 GROUND 9 VSYNC 10 GROUND 3.10 IR Connector All CPU Card provides a 5-pin internal IR communication connector as following CN12 pin information. The CN12 provides for IrDA 1.0 specification application. 27 � CN12 : 5-PIN IR CONNECTOR PIN NO. DESCRIPTION 1 Vcc 2 NC 3 IRRX 4 GROUND 5 IRTX 3.11 Extra Power Connector All CPU Card provides an 8-pin extra DC power connector CN13 for internal power connection at a single board application. Please refer to the following table for detail pin information. � CN13 : 8P Extra Power Connector PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 Vcc 2 +12V 3 -12V 4 GROUND 5 GROUND 6 -5V 7 +12V 8 Vcc 3.12 USB Ports Connector All CPU Card provides two internal 4-pin USB ports connectors. Please refer to the following detail pin information. � CN6, CN7 : 4-pin Header USB connector PIN NO. CN6(USB0) PIN NO. CN7(USB1) 1 Vcc 1 Vcc 2 BD0- 2 BD1- 3 BD0+ 3 BD1+ 4 GROUND 4 GROUND 28 3.13 Flat-Panel Connector ( HS-5200, HS-5000 only ) The CPU Card provides a 44-pin 2.0 mm pitch header connector (CN2) for Flat-Panel connection. Please reference to the following pin-assignment for correct connection to flate panel module. +12V 1 2 +12V GND 3 4 GND PV 5 6 PV CC CC FPVee 7 8 GND P 9 10 P 0 1 P 11 12 P 2 3 P 13 14 P 4 5 P 15 16 P 6 7 P 17 18 P 8 9 P 19 20 P 10 11 P 21 22 P 12 13 P 23 24 P 14 15 P 25 26 P 16 17 P 27 28 P 18 19 P 29 30 P 20 21 P 31 32 P 22 23 GND 33 34 GND SHFCLK 35 36 FLM M 37 38 LP GND 39 40 ENABKL GND 41 42 ASHFCLK V 43 44 V CC CC 29 Chapter-4 AWARD BIOS Setup The board uses Award PCI/ISA BIOS for the system configuration. The Award BIOS setup program is designed to provide the maximum flexibility in configuring the system by offering various options which could be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. To access AWARD PCI/ISA BIOS Setup program, press key during memory testing when first power on. The Main Menu will be displayed at this time. Be notes that only HS-5200 and HS-5200P provides with slot extension PCI bus and ISA bus functions. And the HS-5000 and HS-5000P provides with ISA bus function only. The relative setup on PCI in the BIOS may not cause any activity to HS-5000 and HS-5000P. 30 4.1 Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu will appear on the screen. The Main Menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press to enter the sub-menu. Note that a brief description of each highlighted selection appears at the bottom of the screen. 31 4.2 Standard CMOS Setup The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Floppy/Hard Disk Drive settings. Please refer to the following screen for the setup. When the IDE hard disk drive you are using is larger than 528MB, please set the HDD mode to LBA mode. Please use the IDE Setup Utility in BIOS SETUP to install the HDD correctly. 32 4.3 BIOS Features Setup This section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot-up sequence, keyboard operation, shadowing and security. 33 4.4 Chipset Features Setup This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications between the conventional ISA and PCI buses. It must be stated that these items should never be altered. The default settings have been chosen because they provide the best operating conditions for your system. You might consider and make any changes only if you discover that the data has been lost while using your system. 34 4.5 Integrated Peripherals The IDE hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship that is determined by the cabling configuration used to attach them to the controller. Your system supports two IDE controllers--a primary and a secondary--so you can install up to four separate hard disks. PIO means Programmed Input /Output. Rather than having the BIOS issue a series of commands to affect the transfer to or from the disk drive, PIO allows the BIOS to tell the controller what it wants and then let the controller and the CPU perform the complete task by them. This is much simpler and more efficient (also faster). 35 4.6 Power Management Setup The Power Management Setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use. 36