PBE-1000 ETX Evaluation Board with standard ATX form factor AT Power Connector COM4 DIO ATX Power Connector CF Socket COM3 Debug port Display FCC Features DiskOnChip2000 Socket ✱✱✱✱✱ATX Form Factor IDE1 IDE2 ✱✱✱✱✱4 PCI, 3 ISA extensions ETX Connector ✱✱✱POST Code Diagnostics✱✱ Front Panel TV out ✱✱✱✱✱Secondary Multi I/O LVDS ✱✱✱✱✱Audio Amplifier COM2 ✱✱✱CompactFlash or DiskOnChip K/B and✱✱ Mouse port ✱✱✱✱✱AT or ATX power source RJ-45 LPT Audio ISA Slot x 3 COM1 VGA PCI Slot x4 Connector ✱✱✱✱✱Optional cabling kit Specifications  Expansion Bus:Four 32-bit PCI Slots on Board What is included onboard? Three16-bit ISA Slots on Board The evaluation board is designed in a standard ATX form factor and  Enhanced IDE: Support 4 IDE Devices with Ultra DMA/100 mode allows addition of commercial available add on cards. It can be used  Parallel Port: SSP, ECP, and EEP mode free standing or simply be mounted in a commercial ATX desktop case.  Serial Port: 4 COMs The board includes connectors and interfaces for PS/2 Keyboard and  KB/Mouse Connector: Two keyboard/Mouse connector Mouse, USB, Serial, Parallel, Ethernet, Sound, Floppy and IDE. It  USB Connector: 4 USB ports supports the connection of a wide variety of visual devices such as Flat  Single LAN: RJ45 Panel TTL/LVDS displays, CRT displays and has a TV-Out port.  Audio: Line In/Out, Speakers Supported storage media include CompactFlash, DiskOnChip and other ATA based devices such as harddisk and CDROM. Power is supplied by  Video: TV Out (NTSC, PAL), TTL, LVDS 32-bit means of an AT or an ATX power connector Additional ATX soft switch  Digital I/O: 16-bit On/Off and Reset switches are included on board. All evaluation boards come standard with a Dual LED POST function that monitors and gives POST Code Display information about the BIOS when booting the system. Integrated POST diagnostic function with Dual LED readout that provides detailed debug information on the booting process of the ETX system. Advantage Secondary Super I/O Controller Since the board adheres to the standard ATX form factor it allows addition of commercial available add on cards. This way you can extend Secondary I/O controller on the Evaluation board supports the functionality of our off the shelve ETX cores to match your  Secondary parallel port (LPT2) application requirements. Thus, the created functional prototype can  Primary Floppy port for connection of up to 2 FDDs now be used in a very early project stage for hardware evaluation,  Additional serial ports (COM3 and COM4), secondary I/O controller software development or debugging of your final application. In the supports is integrated in BIOS of ETX modules meanwhile development of a custom ETX carrier board that integrates all these additional function takes place in a separate effort. Develop- Audio Amplifier ment time of custom ETX carrier boards is a minimal effort that takes An onboard LM4880 provides dual audio power amplification capable normally around one or two months. By using the ETX module that of delivering typically 250mW per channel of power to an 8Ohm load. starts from a ready available system core and only requires hardware design for additional functionality to maximize your solution in time and Flash Disk cost.  CompactFlash socket supports Type I/II cards  32-pin DIP socket supports M-Systems DiskOnChip2000 Environment & Power Consumption Ordering Information  Standard AT type: P9/P8 12-pin connector  ATX type: 20-pin source with 3-pin ATX control PBE-1000 Page 1-7 ATX form factor ETX evaluation board with POST, secondary I/O,  Selection: Through BIOS Audio Amplifier and Flash Disk sockets. Cabling Kit Mechanical 6910610000010  Weight: 0.51 kg (1.12 Ib) Complete cabling kit for connection to onboard headers of:  Dimension (L x W): 305 x 192 mm (12" x 7.6") 1 x TV-out, 1 x USB, 2 x IDE, 3 x serial ports www .arbor .com.tw 1-7 Modular Computing