VEZ-2S32-SC Brand Name MARK 10 POWERLINE Ballast Type Electronic Dimming Starting Method Programmed Start Lamp Connection Series Input Voltage 277 Electrical Specifications Input Frequency 50/60 HZ Status Active Lamp Type Num. Rated Min. Input Input Power Ballast Factor MAX Power Lamp B.E.F. of Lamp Start Current (Watts) (min/max) THD Factor Current Lamps Watts Temp (Amps) (min/max) % Crest Factor (°F/C) F17T8 2 17 50/10 0.14 13/38 0.05/1.05 10 0.99 1.6 2.76 F25T8 2 25 50/10 0.20 13/55 0.05/1.05 10 0.99 1.6 1.91 * F32T8 2 32 50/10 0.25 15/68 0.05/1.00 10 0.99 1.6 1.47 Wiring Diagram Enclosure DIMMER RED BLACK YELLOW WHITE BALLAST BLUE LAMP LAMP LINE The wiring diagram that appears above is for the lamp type denoted by the asterisk (*) Enclosure Dimensions OverAll (L) Width (W) Height (H) Mounting (M) Standard Lead Length (inches) 9.50 " 1.7 " 1.18 " 8.90 " 9 1/2 1 7/10 1 9/50 8 9/10 24.1 cm 4.3 cm 3 cm 22.6 cm Revised 10/28/2005 Data is based upon tests performed by Philips Lighting Electronics N.A. in a controlled environment and is representative of relative performance. Actual performance can vary depending on operating conditions. Specifications are subject to change without notice. All specifications are nominal unless otherwise noted. PHILIPS LIGHTING ELECTRONICS N.A. 10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018 Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886 VEZ-2S32-SC Brand Name MARK 10 POWERLINE Ballast Type Electronic Dimming Starting Method Programmed Start Lamp Connection Series Electrical Specifications Input Voltage 277 Input Frequency 50/60 HZ Notes: Status Active Section I - Physical Characteristics 1.1 Ballast shall be physically interchangeable with standard electromagnetic or standard electronic ballasts, where applicable. 1.2 Ballast shall be available in a plastic/metal can or all metal can construction to meet all plenum requirements. 1.3 Ballast shall be provided with poke-in wire trap connectors or integral leads color coded per ANSI C82.11. Section II - Performance Requirements 2.1 Ballast shall be Programmed Start. 2.2 Ballast shall contain auto restart circuitry in order to restart lamps without resetting power. 2.3 Ballast shall operate from 60 Hz input source of 120V, 277V or 347V as applicable with sustained variations of +/- 10% (voltage and frequency). 2.4 Ballast shall be high frequency electronic type and operate lamps at a frequency above 42 kHz to avoid interference with infrared devices and eliminate visible flicker. 2.5 Ballast shall have a Power Factor greater than 0.98 at full light output and greater than 0.90 throughout the dimming range for primary lamp. 2.6 Ballast shall have a minimum ballast factor of 1.00 at maximum light output and 0.05 at minimum light output for primary lamp application. 2.7 Ballast shall provide for a Lamp Current Crest Factor of 1.7 or less. 2.8 Ballast input current shall have Total Harmonic Distortion (THD) of less than 10% at maximum light output when operated at nominal line voltage with primary lamp. Total Harmonic Current (THC) at minimum light output shall not exceed THC at maximum light output. 2.9 Ballast shall have a Class A sound rating. 2.10 Ballast shall have a minimum starting temperature of 10C (50F) for primary lamp. 2.11 Ballast shall provide Lamp EOL Protection Circuit for all T5, T5/HO, and CFL lamps. 2.12 Ballast shall control lamp light output from 100% - 5% relative light output for T8 and CFL lamps and 100% - 1% relative light output for T5/HO lamps. 2.13 Ballast shall ignite the lamps at any light output setting without first going to another output setting. 2.14 Ballast shall tolerate sustained open circuit and short circuit output conditions. Section III - Regulatory Requirements 3.1 Ballast shall not contain any Polychlorinated Biphenyl (PCB). 3.2 Ballast shall be Underwriters Laboratories (UL) listed, Class P and Type 1 Outdoor; and Canadian Standards Association (CSA) certified where applicable. 3.3 Ballast shall comply with ANSI C62.41 Category A for Transient protection. 3.4 Ballast shall comply with ANSI C82.11 where applicable. 3.5 Ballast shall comply with the requirements of the Federal Communications Commission (FCC) rules and regulations, Title 47 CFR part 18, Non-Consumer (Class A) for EMI/RFI (conducted and radiated). 3.6 Ballast shall comply with NEMA 410 for in-rush current limits. Section IV - Other 4.1 Ballast shall be manufactured in a factory certified to ISO 9001 Quality System Standards. 4.2 Ballast shall carry a ____ warranty from date of manufacture against defects in material or workmanship for operation at a maximum case temperature of ____ (Go to our web site for up to date warranty information: www.philips.com/advancewarranty. 4.3 Manufacturer shall have a twenty-year history of producing electronic ballasts for the North American market. 4.4 Ballast shall be controlled by a compatible Mark 10 Powerline two-wire dimmer. 4.5 Ballast shall be Philips Advance part # _____________ or approved equal. Revised 10/28/2005 Data is based upon tests performed by Philips Lighting Electronics N.A. in a controlled environment and is representative of relative performance. Actual performance can vary depending on operating conditions. Specifications are subject to change without notice. All specifications are nominal unless otherwise noted. PHILIPS LIGHTING ELECTRONICS N.A. 10275 WEST HIGGINS ROAD · ROSEMONT, IL 60018 Tel: 800-322-2086 · Fax: 888-423-1882 · www.philips.com/advance Customer Support/Technical Service: 800-372-3331 · OEM Support: 866-915-5886